2005-2008 Yaris · Service Manual TRANSMISSION

P0703 Brake Switch "B" Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

When the brake pedal is depressed, stop light switch signal STP turns on and stop light switch signal ST1- turns off. The transmission control ECU detects the brake pedal condition (whether the pedal is depressed or released) from those signal input. If the signal conditions, STP and ST1-, do not match the standard condition, the transmission control ECU interprets this as a malfunction in the stop light switch circuit and sets the DTC.
DTC No.
DTC Detection Conditions
Trouble Areas
P0703
Following conditions detected simultaneously for 1.0 second or more
(1 trip detection logic)
  1. Ignition switch on (IG)
  2. STP signal OFF
  3. ST1- signal OFF
  1. Open or short in STP or ST1- signal circuits
  2. Stop light switch assembly
  3. Transmission control ECU

WIRING DIAGRAM

C127406E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Data List / Brake Switch Signal1, Brake Switch Signal2 and STP Switch Signal.

  1. Read the value, and check the stop light operation.

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    Brake Switch Signal1
    [Brake SW Sig1]
    Brake switch signal (STP):
    OFF or ON
    ON: Brake pedal depressed
    OFF: Brake pedal released
    STP terminal signal of transmission control ECU
    Brake Switch Signal2
    [Brake SW Sig2]
    Brake switch signal (ST1-):
    OFF or ON
    OFF: Brake pedal depressed
    ON: Brake pedal released
    ST1- terminal signal of transmission control ECU

    OK:
    The normal conditions listed above are shown on the tester when the brake pedal is operated.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
C111590E02
  1. Disconnect the stop light switch assembly connector.

  1. Check the resistance.

    Standard resistance:
    Switch Positions
    Tester Connections
    Specified Conditions
    Switch pin released
    1-2
    Below 1 Ω
    Switch pin released
    3-4
    10 kΩ or higher
    Switch pin pushed in
    1-2
    10 kΩ or higher
    Switch pin pushed in
    3-4
    Below 1 Ω

  1. Reconnect the stop light switch assembly connector.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BATTERY)
C114387E02
  1. Disconnect the stop light switch assembly connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of stop light switch assembly connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    A13-2 - Body ground
    10 to 14 V
    A13-3 - Body ground
    10 to 14 V

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT TRANSMISSION CONTROL ECU ASSEMBLY
C112718E05
  1. Disconnect the transmission control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of transmission control ECU connector.

    Standard voltage:
    Pedal Conditions
    Tester Connections
    Specified Conditions
    Depressed
    STP (D79-34) - Body
    ground
    10 to 14 V
    Released
    STP (D79-34) - Body
    ground
    Below 1 V
    Depressed
    ST1- (D79-35) - Body
    ground
    Below 1 V
    Released
    ST1- (D79-35) - Body
    ground
    10 to 14 V

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - TRANSMISSION CONTROL ECU)
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0603 Internal Control Module Keep Alive Memory (KAM) Error (+ P0613) (from Nov 2005)P0715 Input / Turbine Speed Sensor Circuit Malfunction (from Nov 2005) →