2005-2008 Yaris · Service Manual TRANSMISSION

P0910 Gate Select Actuator Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

C112283E04
The shift and select actuator is operated by the transmission control ECU and changes the transmission gear through the shift and select lever shaft movement. An electric motor (select motor) moves the shift and select lever shaft in the select direction, and the select stroke sensor, which is mounted on the shift and select actuator assembly, detects the select position. The transmission control ECU monitors the electrical current and select motor output terminal voltage, and detects malfunctions in the select motor circuit.
DTC No.
DTC Detection Conditions
Trouble Areas
P0910
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Select motor is not energized
  2. Select motor voltage is less than 0.5 V*1, or more than threshold*2 for 0.5 seconds
  3. +BM voltage is 10 V or more
  1. Shift and select actuator assembly (select motor)
  2. Short in select motor circuit
  3. Transmission control ECU
P0910
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Select motor is energized
  2. Target select motor current is more than 5A
  3. Actual select motor current is less than 1A*3
  1. Shift and select actuator assembly (select motor)
  2. Open in select motor circuit
  3. Transmission control ECU
P0910
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Select motor is not energized
  2. Difference between maximum and minimum voltages of select motor terminal (MSL+ or MSL-) is more than threshold*4 for 0.5 seconds
  3. +BM voltage is 10 V or more
  1. Shift and select actuator assembly (select motor)
  2. Open in select motor circuit
  3. Transmission control ECU
  1. *1: A short between the select motor circuit and the body ground is suspected.
  2. *2: A short between the select motor circuit and the +B circuit is suspected.
  3. *3: An open in the select motor circuit is suspected. When the motor current does not flow to the ECU terminals despite the ECU ordering the select motor to operate, the ECU sets the DTC.
  4. *4: An open in the select motor circuit is suspected. When the difference is more than the threshold despite the ECU not ordering the select motor to operate, the ECU sets the DTC.

WIRING DIAGRAM

C111577E02

INSPECTION PROCEDURE

NOTICE:
In select stroke sensor or shift and select actuator assembly replacement, perform the [Initialization and Learning] procedure (Click here) and [Synchronization Position Calibration] procedure (Click here) after installing the sensor or actuator assembly. If the sensor or actuator is installed without performing [Initialization and Learning] and [Synchronization Position Calibration], it may cause driving performance degradation or system component breakage.


1. INSPECT SHIFT AND SELECT ACTUATOR ASSEMBLY
C121803E01
  1. Disconnect the select motor connector.

  1. Measure the select motor resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    0.1 to 100 Ω

  1. Reconnect the select motor connector.



NG
REPLACE SHIFT AND SELECT ACTUATOR ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (SHIFT AND SELECT ACTUATOR - TRANSMISSION CONTROL ECU)
C113924E09
  1. Disconnect the select motor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    MSL- (A37-4) - (C62-1)
    Below 1 Ω
    MSL+ (A37-5) - (C62-2)
    Below 1 Ω
    MSL- (A37-4) - Body ground
    10 kΩ or higher
    MSL+ (A37-5) - Body ground
    10 kΩ or higher

  1. Reconnect the select motor connector.

  1. Reconnect the transmission control ECU connector



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0909 Gate Select Control Error (from Nov 2005)P0915 Gear Shift Position Circuit (Range / Performance) (+ P0916, P0917) (from Nov 2005) →