2005-2008 Yaris · Service Manual TRANSMISSION

P0885 TCM Power Relay Control Circuit (Open)

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The multi-mode manual transmission system has a dedicated power supply circuit. While the ignition switch is turned on (IG), the transmission control ECU outputs the power from the MREL terminal to operate the AMT relay. Then, the power is supplied to the +BM terminal of the transmission control ECU through the AMT relay. The voltage (+BM) is monitored and when it is low (6.29 V or less) despite the voltage is supplied to MREL circuit, the transmission control ECU determines that there is a malfunction in the multi-mode manual transmission system and sets a DTC. When the voltage (+BM) is high (6.29 V or more) although the voltage is not supplied to the MREL circuit, the transmission control ECU sets a DTC.
DTC No.
DTC Detecting Conditions
Trouble Areas
P0885
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. Voltage is supplied to MREL circuit
  2. +BM voltage is less than 6.29 V for 0.5 seconds
  1. AMT fuse
  2. AMT relay
  3. Open in MREL signal circuit
  4. Open in PGND signal circuit
  5. Open in +BM signal circuit
  6. Transmission control ECU
P0887
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. No voltage is supplied to MREL circuit
  2. +BM voltage is more than 6.29 V for 0.5 seconds
  1. AMT relay
  2. Short in MREL signal circuit
  3. Short in PGND signal circuit
  4. Short in +BM signal circuit
  5. Transmission control ECU

WIRING DIAGRAM

C110758E03

INSPECTION PROCEDURE


1. INSPECT RELAY
B057491E02
  1. Remove the AMT relay from engine room R/B No. 2 (engine room R/B No.7).

    HINT:
    The AMT relay is located in:
    Engine room R/B No.2: Without daytime running light system
    Engine room R/B No.7: With daytime running light system

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    When battery voltage applied to terminals 1 and 2

  1. Reinstall the AMT relay.



NG
REPLACE RELAY
OK


2. INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (+BM TERMINAL INPUT VOLTAGE)
C112719E03
  1. Disconnect the transmission control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the transmission control ECU connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +BM (A37-2) - PGND (A37-8)
    10 to 14 V

  1. Turn the ignition switch off.

  1. Measure the voltage between the terminals of the transmission control ECU connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +BM (A37-2) - PGND (A37-8)
    Below 1 V

  1. Reconnect the transmission control ECU connector.



OK
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
NG


3. INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (MREL TERMINAL OUTPUT VOLTAGE)
C112714E14
  1. Measure the voltage between the terminal of the transmission control ECU and the body ground when the ignition switch is turned on (IG) and off.

    Standard voltage:
    Tester Connections
    Ignition Switch
    Specified Conditions
    MREL (A38-5) - Body
    ground
    Off
    Below 1 V
    MREL (A38-5) - Body
    ground
    On (IG)
    10 to 14 V



NG
Go to step 4
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MREL - AMT RELAY - GND, +BM - AMT RELAY - BATTERY)

4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT BETWEEN MREL AND GND)
C112715E07
  1. Disconnect the transmission control ECU connectors.

  1. C129093E01
    Remove the AMT relay from engine room R/B No. 2 (engine room R/B No. 7).

  1. Check the resistance.

    Standard resistance (Check for Short):
    Tester Connections
    Specified Conditions
    MREL (A38-5) or AMT relay (1) - Body ground
    10 kΩ or higher

  1. Check the voltage between the specified terminal and the body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    MREL (A38-5) or AMT relay (1) - Body ground
    Below 1 V

  1. Reconnect the transmission control ECU connectors.

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0821 Gear Lever "X" Position Circuit (from Nov 2005)P0900 Clutch Actuator Circuit (from Nov 2005) →