2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.


1. INSTALL AMPLIFIER ANTENNA ASSEMBLY

E107786
  1. Set the amplifier antenna into the hole in the roof, and place the amplifier antenna cord in the cutout of the amplifier antenna.

  1. Install the amplifier antenna with the antenna nut.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. E107783
    Engage the 5 clamps.


2. INSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

  1. E107781
    Install the roof antenna pole by turning it in the direction of the arrow shown in the illustration.


3. INSTALL ROOF HEADLINING ASSEMBLY

  1. w/ Curtain Shield Airbag:

    1. Engage the 4 hooks and install the roof headlining.

    2. Install the clip.

      B138509

  1. w/o Curtain Shield Airbag:

    1. Engage the 2 claws and the 4 hooks and install the roof headlining.

    2. Install the clip.

      B138510

  1. B114512
    Install the 2 connectors.

  1. Connect the 2 connectors.

  1. Install the antenna cord onto the antenna cord clamp.


4. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    Insert the hook into the body hole.

  1. Engage the clip and install the front No. 2 speaker.

  1. B127674
    Connect the speaker connector.

  1. B114312
    Install the 3 clamps.

  1. Connect the connector.

  1. B117697E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B117694
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


5. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    Insert the hook into the body hole.

  1. Engage the clip and install the front No. 2 speaker.

  1. B127673
    Connect the speaker connector.

  1. B114316
    Install the 4 clamps.

  1. B117698E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B114318
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


6. INSTALL MAP LIGHT ASSEMBLY

  1. B114310
    Connect the map light connector.

  1. B114346
    Engage the 4 claws and install the map light.


7. INSTALL ROOM LIGHT ASSEMBLY

  1. B114347
    Engage the 4 claws and install the room light switch base.

  1. Install the roof wire onto the claw of the room light.

  1. B124366
    Engage the 4 claws and install the 2 covers.

  1. B114348
    Engage the 4 claws and install the room light.

  1. B114349
    Engage the 4 claws and install the room light lens.


8. INSTALL VISOR HOLDER RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


9. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


10. INSTALL VISOR ASSEMBLY RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


11. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


12. INSTALL ASSIST GRIP SUB-ASSEMBLY

B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.


13. INSTALL ASSIST GRIP COVER

B114352

HINT:
The number of the assist grip covers varies with specifications.

  1. Engage the 2 claws and install the assist grip cover.


14. INSTALL COAT HOOK (w/ Coat Hook)

  1. B127667
    Engage the 2 claws and install the coat hook.

  1. B127668
    Engage the 2 claws and close the cover.


15. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)

B114353

HINT:
The number of the roof headlining service hole covers varies with specifications.

  1. Install the roof headlining service hole cover.


16. INSTALL SEAT BELT ANCHOR COVER

  1. B114467
    Engage the 4 claws and install the seat belt anchor cover.


17. INSTALL REAR ROOF SIDE RAIL GARNISH RH

  1. B114508
    Engage the 4 clips and install the rear roof side rail garnish.


18. INSTALL REAR ROOF SIDE RAIL GARNISH LH

HINT:
Use the same procedure as for the RH side.


19. INSTALL ROOF SIDE INNER GARNISH RH

  1. B114504E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114505
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.


20. INSTALL ROOF SIDE INNER GARNISH LH

  1. B114506E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114507
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.


21. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B114468
    Engage the 4 claws and install the center belt guide.

  1. B114461
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114469
    Engage the 2 claws and close the slip joint cover.

  1. B114459
    Install the 2 tongue plates.


22. INSTALL CENTER PILLAR UPPER GARNISH RH

  1. B114503
    Engage the 2 clips and install the center pillar upper garnish.


23. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


24. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114479
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


25. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


26. INSTALL SEAT BELT ANCHOR COVER CAP

B114478

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the seat belt anchor cover cap.


27. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

  1. B114501
    Engage the 3 clips and the 3 claws and install the deck side trim panel.

  1. Tighten the 3 screws.


28. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B114502
    Connect the luggage compartment room light connector.

  1. Engage the 3 clips and the 3 claws and install the deck side trim panel.

  1. Tighten the 3 screws.


29. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

  1. B114500
    Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


30. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


31. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


32. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

  1. B114499
    Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.

  1. B114498
    Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.


33. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


34. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH

  1. B114759
    Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


35. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


36. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B114546E01
    Align the locating mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Blue
    LH side
    Pink


37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


38. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the claw and stud bolt and install the cowl side trim board.


39. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


40. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH

  1. B114571
    Engage the 4 claws and install the instrument panel under cover.


41. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.


42. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114494
    Engage the 8 claws and install the front door scuff plate.


43. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


44. INSTALL REAR SEAT ASSEMBLY RH

  1. B124326E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124299E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


45. INSTALL REAR SEAT ASSEMBLY LH

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


46. INSTALL NO. 1 REAR SEAT LEG COVER

  1. B124298
    Engage the 4 claws and install the rear seat No. 1 leg cover.


47. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


48. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


49. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


50. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


51. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


52. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138393
    Install the spare wheel cover.


53. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


54. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →