2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Nov 2005

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.


1. INSTALL ROOF HEADLINING ASSEMBLY

  1. B114340
    Pull the roof headlining back into the vehicle through the back door.

  1. w/ Curtain Shield Airbag:

    1. Engage the 4 hooks and install the roof headlining.

    2. Install the clip.

      B114324

  1. w/o Curtain Shield Airbag:

    1. Engage the 2 claws and the 4 hooks and install the roof headlining.

    2. Install the clip.

      B114322

  1. B114321
    Install the 2 connectors.

  1. Connect the 2 connectors.

  1. Install the antenna cord onto the clamp.

  1. B114511
    for LHD:

    1. Connect the connector.

    2. Install the clamp.

  1. B114320
    for RHD:

    1. Connect the connector.

    2. Install the roof wire into the claw of the junction block.

    3. B114319
      Install the clamp.


2. INSTALL INSTRUMENT PANEL BOX (for LHD)

B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.


3. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


5. INSTALL NO. 1 SWITCH HOLE BASE (for LHD)

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


6. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


7. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


8. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


9. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


10. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    Insert the hook into the body hole.

  1. Engage the clip and install the front No. 2 speaker.

  1. B127674
    Connect the speaker connector.

  1. B114312
    Install the 3 clamps.

  1. Connect the connector.

  1. B117697E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B117694
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


11. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    Insert the hook into the body hole.

  1. Engage the clip and install the front No. 2 speaker.

  1. B127673
    Connect the speaker connector.

  1. B114316
    Install the 4 clamps.

  1. B117698E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B114318
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


12. INSTALL MAP LIGHT ASSEMBLY

  1. B114310
    Connect the map light connector.

  1. B114346
    Engage the 4 claws and install the map light.


13. INSTALL ROOM LIGHT ASSEMBLY

  1. B114347
    Engage the 4 claws and install the room light switch base.

  1. Install the roof wire onto the claw of the room light.

  1. B124366
    Engage the 4 claws and install the 2 covers.

  1. B114348
    Engage the 4 claws and install the room light.

  1. B114349
    Engage the 4 claws and install the room light lens.


14. INSTALL VISOR HOLDER RH

  1. B114350E01
    Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.


15. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


16. INSTALL VISOR ASSEMBLY RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


17. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


18. INSTALL ASSIST GRIP SUB-ASSEMBLY

B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.


19. INSTALL ASSIST GRIP COVER

B114352

HINT:
The number of the assist grip covers varies with specifications.

  1. Engage the 2 claws and install the assist grip cover.


20. INSTALL COAT HOOK (w/o Curtain Shield Airbag)

  1. B127667
    Engage the 2 claws and install the coat hook.

  1. B127668
    Engage the 2 claws and close the cover.


21. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)

B114353

HINT:
The number of the roof headlining service hole covers varies with specifications.

  1. Install the roof headlining service hole cover.


22. INSTALL SEAT BELT ANCHOR COVER

  1. B114467
    Engage the 4 claws and install the seat belt anchor cover.


23. INSTALL CENTER PILLAR UPPER GARNISH RH

  1. B114298
    Engage the 3 clips and the 2 hooks and install the center pillar upper garnish.


24. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


25. INSTALL CENTER PILLAR LOWER GARNISH RH

  1. B114297
    Engage the 2 clips and the 2 claws and install the center pillar lower garnish.


26. INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:
Use the same procedure as for the RH side.


27. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114296
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


28. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


29. INSTALL SEAT BELT ANCHOR COVER CAP

B114421

HINT:
Use the same procedure for both sides.

  1. Engage the 3 claws and install the seat belt anchor cover cap.


30. INSTALL ROOF SIDE INNER GARNISH RH

  1. B114576E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.

  1. B114575
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.


31. INSTALL ROOF SIDE INNER GARNISH LH

  1. B114578E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.

  1. B114577
    w/ Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.


32. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B114468
    Engage the 4 claws and install the center belt guide.

  1. B114461
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114469
    Engage the 2 claws and close the slip joint cover.

  1. B114459
    Install the 2 tongue plates.


33. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

  1. B114573
    Engage the 3 clips and the 6 claws and install the deck trim side panel.

  1. Tighten the 3 screws.


34. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B114574
    Connect the luggage compartment room light connector.

  1. Engage the 3 clips and the 6 claws and install the deck trim side board.

  1. Tighten the 3 screws.


35. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

  1. B130498
    Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114289
    Install the belt.


36. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130370E01
    Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Green
    LH side
    Red


38. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


39. INSTALL REAR DOOR SCUFF PLATE RH

  1. B114287
    Engage the 6 claws and install the rear door scuff plate.


40. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B130371E01
    Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    White
    LH side
    Yellow


42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


43. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the claw and stud bolt and install the cowl side trim board.


44. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


45. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH

  1. B114571
    Engage the 4 claws and install the instrument panel under cover.


46. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.


47. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114284
    Engage the 8 claws and install the front door scuff plate.


48. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


49. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


50. INSTALL REAR SEAT ASSEMBLY RH

  1. B124326E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124299E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


51. INSTALL REAR SEAT ASSEMBLY LH

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


52. INSTALL NO. 1 REAR SEAT LEG COVER

  1. B124298
    Engage the 4 claws and install the rear seat No. 1 leg cover.


53. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


54. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


55. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


56. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


57. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


58. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138392
    Install the rear floor carpet.


59. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


60. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


61. INSPECT SRS WARNING LIGHT
(Click here)
← REASSEMBLY (from Nov 2005)COMPONENTS (from Jan 2006) →