REMOVAL
Removal / installation · Vehicles built from Aug 2005
| 1. POSITION WHEELS FACING STRAIGHT AHEAD |
| 2. REMOVE BATTERY |
Disconnect the cable from the battery terminal.
Loosen the nut and remove the battery clamp.
Remove the battery.
| 3. REMOVE BATTERY TRAY |
| 4. REMOVE COLUMN HOLE COVER SILENCER SHEET |
Remove the floor carpet and 2 clips and remove the column hole cover silencer.

| 5. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY |
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.
| 6. SEPARATE STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO.1 |
| 7. REMOVE FRONT WHEELS |
| 8. REMOVE ENGINE UNDER COVER LH |
| 9. REMOVE ENGINE UNDER COVER RH |
| 10. DRAIN AUTOMATIC TRANSAXLE FLUID |
Remove the drain plug and gasket, and drain the ATF.
Install a new gasket and the drain plug.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| 11. REMOVE HOOD SUB-ASSEMBLY |
Remove the 4 bolts and remove the hood.
| 12. REMOVE FRONT WIPER ARM HEAD CAP |
![]() ![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 13. REMOVE FRONT WIPER ARM LH |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.

| 14. REMOVE FRONT WIPER ARM RH |
- HINT:
- Use the same procedure as for the LH side.
| 15. REMOVE HOOD TO COWL TOP SEAL |
![]() ![]() |
Disengage the 7 clips and remove the hood to cowl top seal.
| 16. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() ![]() |
Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.
Disconnect the washer hose.

Disengage the 11 claws and clip.
Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.

| 17. REMOVE COWL TOP VENTILATOR LOUVER LH |
![]() ![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
| 18. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY |
![]() ![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 19. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY RH |
![]() ![]() |
Disengage the claw and remove cowl to register duct sub-assembly No. 2.
| 20. REMOVE COWL TOP PANEL OUTER |
![]() ![]() |
Disengage the wire harness clamp.
Remove the 9 bolts and remove the cowl top panel outer.

| 21. REMOVE CYLINDER HEAD COVER NO.2 |
![]() ![]() |
Remove the 4 nuts and cylinder head cover No. 2.
| 22. REMOVE AIR CLEANER ASSEMBLY |
![]() ![]() |
Separate the intake air flow meter connector and wire harness clamp.
Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.
Separate the vacuum switching valve connector and wire harness clamp.
Separate the ventilation hose from the air cleaner hose.
Release the air cleaner cap sub-assembly with air cleaner hose No. 1.
Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and air cleaner hose.
Remove the air cleaner element.
Separate the wire harness clamp from the air cleaner case.

Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.
| 23. REMOVE AIR CLEANER BRACKET |
![]() ![]() |
Separate the wire harness clamp from the air cleaner bracket.
Remove the 2 bolts and remove the air cleaner bracket.
| 24. REMOVE BATTERY CARRIER |
![]() ![]() |
Separate the wire harness clamp from the battery carrier.
Remove the 5 bolts and remove the battery carrier.
| 25. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() ![]() |
Remove the nut and disconnect the control cable from the control shaft lever.
Remove the clip and disconnect the control cable from the control cable bracket.
| 26. SEPARATE ENGINE WIRE NO.3 |
![]() ![]() |
Remove the bolt and separate engine wire No. 3 from the automatic transaxle.
| 27. DISCONNECT CONNECTORS |
Separate the park neutral position switch connector.
Separate the transmission wire connector.
Separate the transmission revolution sensor connector.
| 28. DISCONNECT WIRE HARNESS |
![]() ![]() |
Remove the 2 bolts and separate the 2 wire harness clamp brackets from the automatic transaxle.
Remove the bolt and separate the wire harness clamp bracket from the automatic transaxle

| 29. REMOVE STARTER ASSEMBLY |
![]() ![]() |
Remove the terminal cap.
Remove the nut and disconnect terminal 30.
Disconnect the connector.
Remove the 2 bolts and remove the starter assembly.
| 30. REMOVE FRONT AXLE HUB NUT LH |
![]() ![]() |
Using SST and a hammer, release the staked part of the axle hub nut.
- SST
- 09930-00010
- NOTICE:
- Insert SST into the groove with the flat surface facing up.
- Do not damage the tip of SST using grinders.
- Completely unstake the staked part before removing the axle hub nut.
- Do not damage the threads of the drive shaft.
- Insert SST into the groove with the flat surface facing up.
Using a 30 mm socket wrench, remove the axle hub nut.
| 31. REMOVE FRONT AXLE HUB NUT RH |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 32. SEPARATE FRONT SPEED SENSOR LH |
![]() ![]() |
Remove the bolt and separate the speed sensor and flexible hose.
Remove the bolt and separate the speed sensor from the steering knuckle.

- NOTICE:
- Keep the speed sensor tip and installation portion free of foreign matter.
- Remove the speed sensor without turning it from its original installation angle.
- Keep the speed sensor tip and installation portion free of foreign matter.
| 33. SEPARATE FRONT SPEED SENSOR RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 34. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() ![]() |
Remove the nut and separate the stabilizer link from the shock absorber.
- HINT:
- If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
| 35. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 36. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and castle nut.
Using SST, separate the tie rod end from the steering knuckle.

- SST
- 09628-62011
- NOTICE:
- Do not damage the tie rod end dust cover.
| 37. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 38. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH |
![]() ![]() |
Remove the clip and castle nut.
Using SST, separate the lower arm.

- SST
- 09628-00011
- NOTICE:
- Do not damage the lower ball joint dust cover.
- Suspend SST with a piece of string or the equivalent.
- Do not damage the lower ball joint dust cover.
| 39. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 40. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() ![]() |
Using SST, remove the drive shaft.
- SST
- 09520-01010
09520-24010 (09520-32040)
- NOTICE:
- Do not damage the oil seal.
- Do not damage the inboard joint boot.
- Do not drop the drive shaft.
- Do not damage the oil seal.
| 41. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() ![]() |
Using a screwdriver and hammer, remove the drive shaft.
- NOTICE:
- Do not damage the oil seal.
- Do not damage the inboard joint boot.
- Do not drop the drive shaft.
- Do not damage the oil seal.
| 42. SUSPEND ENGINE ASSEMBLY |
1KR-FE
Remove the bolt and remove the wire harness clamp bracket.
Install the engine hanger with the bolt in the position shown in the illustration.

- Part No.:
- No. 1 engine hanger :
- 12281-40030
- No. 2 engine hanger:
- 12282-40010
- Bolt:
- 91671-80820
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
Using an engine sling device and a chain block, support the engine assembly.
1NZ-FE, 2NZ-FE
Remove the bolt and remove the radio setting condenser.
Remove the bolt and remove the air-fuel ratio sensor wiring bracket.
Install the engine hanger with the bolt in the position shown in the illustration.

- Part No.:
- Engine hanger :
- 12281-21010
- Bolt:
- 91642-81025
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.
| 43. SEPARATE OIL COOLER INLET HOSE |
![]() ![]() |
Separate the oil cooler inlet hose from oil cooler inlet tube No. 1.
| 44. SEPARATE OIL COOLER OUTLET HOSE |
Separate the oil cooler outlet hose from oil cooler outlet tube No. 1.
| 45. SEPARATE ENGINE MOVING CONTROL ROD |
![]() ![]() |
Remove the bolt and nut and separate the engine moving control rod from the bracket.
| 46. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Remove the bolt and separate the engine moving control rod.

Support the front suspension crossmember with a transmission jack.
Remove the 6 bolts and remove the suspension crossmember.

| 47. REMOVE ENGINE MOVING CONTROL ROD BRACKET |
![]() ![]() |
Remove the 3 bolts and remove the engine moving control rod bracket.
| 48. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY |
Support the automatic transmission with the transmission jack.
| 49. SEPARATE ENGINE MOUNTING INSULATOR LH |
![]() ![]() |
Remove the bolt and nut and separate the engine mounting insulator LH from the bracket.
| 50. REMOVE ENGINE MOUNTING BRACKET LH |
![]() ![]() |
Remove the 4 bolts and remove the engine mounting bracket LH from the automatic transaxle.
| 51. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY |
![]() ![]() |
Remove the flywheel housing under cover.
Remove the 6 torque converter set bolts while holding the crankshaft pulley bolt with a wrench.

Remove the 7 bolts and remove the automatic transmission from the engine.

| 52. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY |
Remove the torque converter clutch from the automatic transaxle.
| 53. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 |
![]() ![]() |
Remove the 2 bolts and remove transmission control cable bracket No. 1 from the automatic transaxle.
| 54. SEPARATE OIL COOLER INLET TUBE NO.1 |
![]() ![]() |
Using SST, remove the oil cooler inlet tube while holding the oil cooler tube union with a spanner.
- SST
- 09023-12701
| 55. SEPARATE OIL COOLER OUTLET TUBE NO.1 |
![]() ![]() |
Using SST, remove the oil cooler outlet tube while holding the oil cooler tube union with a spanner.
- SST
- 09023-12701
| 56. REMOVE OIL COOLER TUBE CLAMP NO. 1 |
![]() ![]() |
Remove the bolt and remove oil cooler tube clamp No. 1 from the oil filler tube.
Remove the oil cooler inlet tube and the oil cooler outlet tube from the automatic transaxle.
| 57. REMOVE TRANSMISSION OIL LEVEL GAGE SUB-ASSEMBLY |
Remove the oil level gauge from the oil filler tube.
| 58. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY |
![]() ![]() |
Remove the bolt and remove the oil filler tube.
Remove the O-ring from the oil filler tube.
































