2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

C121659
  1. Remove the bolt and remove the speedometer driven hole cover.

  1. Remove the O-ring from the speedometer driven hole cover.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C117101
  1. Remove the nut and washer and remove the control lever shaft.

  1. C117104
    Using a screwdriver, pry out the lock plate and remove the manual valve shaft nut.

  1. C117106
    Remove the 2 bolts and pull out the park/neutral position switch assembly.


3. REMOVE TRANSMISSION REVOLUTION SENSOR

C067751
  1. Remove the bolt and remove the transmission revolution sensor.


4. REMOVE OIL COOLER TUBE UNION

D025286
  1. Remove the 2 oil cooler tube unions from the transaxle case.

  1. Remove the 2 O-rings from the 2 oil cooler tube unions.


5. REMOVE TRANSAXLE CASE NO. 1 PLUG

C067754
  1. Remove the 4 transaxle case No. 1 plugs from the transaxle housing and transaxle case.

  1. C067755
    Remove the transaxle case No. 1 plug from the transaxle case.

  1. Remove the O-rings from the transaxle case No. 1 plugs.


6. REMOVE BREATHER PLUG HOSE

C067752
  1. Remove the breather plug hose from the transaxle case.


7. FIX AUTOMATIC TRANSAXLE ASSEMBLY

8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

C062684E03
  1. Remove the 19 bolts and remove the oil pan and oil pan gasket.

  1. C093943E04
    Remove the 2 oil cleaner magnets from the oil pan.

  1. Examine the particles in the pan.

    1. Collect any steel chips with the removed magnets.
      Carefully look at the foreign matter and particles in the pan and on the magnets to predict the type of wear which might be found in the transaxle.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bearing wear


9. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C062685E02
  1. Remove the 3 bolts and remove the oil strainer assembly.

  1. D005904E04
    Remove the oil strainer gasket from the oil strainer.


10. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
  1. Disconnect the 5 solenoid connectors.

  1. C093938E05
    Remove the bolt and lock plate and remove the ATF temperature sensor.

  1. C093939E07
    Remove the 2 bolts and remove the detent spring cover and detent spring.

  1. C093940E10
    Remove the 13 bolts and the valve body assembly from the transaxle case.


11. REMOVE TRANSMISSION WIRE

C062929
  1. Remove the bolt and the transmission wire from the transaxle case.

  1. C067760
    Remove the O-ring from the transmission wire.


12. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

C067757
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.


13. REMOVE TRANSAXLE CASE GASKET

C067758
  1. Remove the transaxle case gasket from the transaxle case.


14. REMOVE BRAKE DRUM GASKET

C067759
  1. Remove the brake drum gasket from the transaxle case.


15. REMOVE CHECK BALL BODY

C067767
  1. Remove the check ball body and spring from the transaxle case.


16. REMOVE B-2 ACCUMULATOR PISTON

C067761
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.

  1. D025038
    Remove the 2 O-rings from the B-2 accumulator piston.


17. REMOVE C-3 ACCUMULATOR PISTON

C067762
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.

  1. D025039
    Remove the 2 O-rings from the C-3 accumulator piston.


18. REMOVE C-2 ACCUMULATOR PISTON

C067763
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.

  1. D025040
    Remove the 2 O-rings from the C-2 accumulator piston.


19. REMOVE TRANSAXLE HOUSING

D025041
  1. Remove the 14 bolts.

  1. Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential gear assembly may be accidentally removed when the transaxle housing is removed.


20. INSPECT INPUT SHAFT END PLAY

C067772
  1. Measure the end play in the axial direction.

    End play:
    0.37 to 1.29 mm (0.0146 to 0.0508 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.


21. REMOVE OIL PUMP ASSEMBLY

C067773
  1. Remove the 7 bolts and the oil pump assembly from the transaxle case.


22. REMOVE DIFFERENTIAL GEAR ASSEMBLY

D025042
  1. Remove the differential gear assembly from the transaxle case.


23. REMOVE OVERDRIVE BRAKE GASKET

C067783
  1. Using a screwdriver, remove the 2 overdrive brake gaskets from the transaxle case.


24. REMOVE INPUT SHAFT ASSEMBLY

C067775
  1. Remove the input shaft assembly from the transaxle case.


25. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C067782
  1. Remove the thrust needle roller bearing from the input shaft.


26. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C067776
  1. Remove the thrust needle roller bearing from the forward clutch hub.


27. INSPECT INTERMEDIATE SHAFT ASSEMBLY

D025043
  1. Using a dial indicator, measure the clearance of the intermediate shaft.

    Standard clearance:
    0.204 to 0.966 mm (0.008 to 0.038 in.)


28. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C067777
  1. Remove the forward clutch hub from the transaxle case.


29. REMOVE TRANSAXLE REAR COVER ASSEMBLY

C067778
  1. Remove the 11 bolts.

  1. Tap around the circumference of the transaxle rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.


30. REMOVE TRANSAXLE CASE GASKET

C067779
  1. Remove the 4 transaxle case gaskets.


31. REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C067780
  1. Using a magnetic finger, remove the thrust needle roller bearing.


32. REMOVE INTERMEDIATE SHAFT ASSEMBLY

C067781
  1. Remove the intermediate shaft assembly from the transaxle case.


33. REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC

C067785
  1. Remove the flange, 2 discs and 2 flanges No. 2 from the transaxle.


34. REMOVE THRUST NEEDLE ROLLER BEARING

C067784
  1. Using a magnetic finger, remove the C-2 hub thrust bearing race, the thrust needle roller bearing and the thrust bearing race from the direct clutch hub.


35. REMOVE DIRECT CLUTCH HUB

C068196
  1. Remove the direct clutch hub from the transaxle case.


36. REMOVE REAR PLANETARY SUN GEAR NO. 2 THRUST NEEDLE ROLLER BEARING

C067786
  1. Using a magnetic finger, remove the thrust bearing from the rear thrust needle bearing.


37. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

C067973
  1. Remove the rear planetary sun gear from the transaxle case.


38. REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

C068161
  1. Remove the rear planetary sun gear thrust needle roller bearing and thrust washer No. 1 from the rear planetary sun gear.


39. INSPECT 1-WAY CLUTCH ASSEMBLY

D025044E07
  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that 1-way clutch turns freely counterclockwise and locks when turned clockwise.


40. REMOVE 1-WAY CLUTCH ASSEMBLY

C068163
  1. Remove the 1-way clutch assembly and planetary carrier thrust washer No. 2 from the rear planetary sun gear.


41. REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C067971
  1. Using a screwdriver, remove the snap ring from the transaxle case.


42. REMOVE 2ND BRAKE BRAKE DISC

C067969
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle.


43. REMOVE 2ND BRAKE PISTON SLEEVE

C067970
  1. Remove the 2nd brake piston sleeve from the transaxle case.


44. INSPECT 1-WAY CLUTCH NO. 2

D025045E06
  1. Install the 1-way clutch and the thrust washer onto the rear planetary sun gear.

  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.


45. REMOVE REAR PLANETARY GEAR ASSEMBLY

C067967
  1. Using a screwdriver, remove the snap ring.

  1. Remove the rear planetary gear assembly from the transaxle case.


46. REMOVE PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

C068159
  1. Remove the thrust needle roller bearing and 2 bearing races from the rear planetary gear assembly.


47. REMOVE 1-WAY CLUTCH NO. 2

C067966
  1. Separate the 2nd brake cylinder, 1-way clutch No. 2 and the rear planetary gear.


48. REMOVE OUTER RACE RETAINER

C067965
  1. Remove the retainer from 1-way clutch No. 2.


49. REMOVE FRONT PLANETARY SUN GEAR

C068157
  1. Remove the front planetary sun gear and thrust needle roller bearing from the transaxle case.


50. REMOVE 1ST AND REVERSE BRAKE DISC

C067963
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.


51. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D008332E02
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00070  

  1. Remove the 1st and reverse brake return spring sub-assembly.


52. REMOVE 1ST AND REVERSE BRAKE PISTON NO. 2

C068211
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a shop rag or piece of cloth.
    2. Do not splash ATF with the compressed air.


53. REMOVE 1ST AND REVERSE BRAKE PISTON NO. 2 O-RING

C067962
  1. Remove the 2 O-rings from 1st and reverse brake piston No. 2.


54. REMOVE COUNTER DRIVE GEAR NUT

C067960
  1. Fix the counter driven gear with the parking lock pawl.

  1. C067961E01
    Using SST and a hammer, release the lock washer.
    SST
    09930-00010  

  1. D025048E02
    Using SST, remove the nut and lock washer.
    SST
    09387-00120  


55. REMOVE PLANETARY GEAR ASSEMBLY

D025047E01
  1. Using SST and a press, remove the planetary gear assembly from the transaxle case.

    SST
    09950-60010   (09951-00400, 09951-00320, 09952-06010)
    09950-70010   (09951-07100)


56. REMOVE COUNTER DRIVE GEAR

C068474E01
  1. Install the 2 bolts onto the counter drive gear.

    Bolt (M6):
    L = 40 to 80 mm
    Pitch = 1.0 mm

  1. Rotate the 2 bolts and remove the counter drive gear and front planetary sun gear.

  1. Remove the 2 radial ball bearings from the counter drive gear and front planetary sun gear.


57. REMOVE PARKING LOCK PAWL BRACKET

C067957
  1. Remove the 3 bolts, cam guide and bracket from the transaxle case.


58. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

C067956
  1. Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.


59. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

C067954
  1. Using a screwdriver, release and remove the spacer.

  1. C067950
    Using a pin punch and hammer, drive out the manual valve lever shaft spring pin.

  1. Remove the manual valve lever shaft and manual valve lever.


60. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

C067951
  1. Remove the parking lock rod from the manual valve lever.


61. REMOVE MANUAL VALVE LEVER SHAFT

C067952
  1. Remove the manual valve lever shaft from the transaxle case.


62. REMOVE PARKING LOCK PAWL

C067948
  1. Using a screwdriver, remove the parking lock pawl shaft from the transaxle case.

  1. Remove the parking lock pawl torsion spring and parking lock pawl from the transaxle case.


63. REMOVE COUNTER DRIVEN GEAR

C068164
  1. Remove the counter driven gear, drive pinion and thrust needle roller bearing from the transaxle case.


64. REMOVE DIFFERENTIAL DRIVE PINION PLUG

C068188
  1. Using a brass bar and a hammer, remove the differential drive pinion plug.


65. REMOVE DIFFERENTIAL DRIVE PINION

D025174E01
  1. Using SST and a press, remove the differential drive pinion from the counter driven gear.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07150)


66. REMOVE BEARING LOCK PLATE

C067770
  1. Remove the bolt and remove the bearing lock plate.


67. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

C068187
  1. Remove the differential gear lube apply tube from the transaxle housing.


68. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

C067771E02
  1. Using SST, remove the front drive pinion front tapered roller bearing from the transaxle housing.

    SST
    09308-10010  


69. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

C067946E03
  1. Using SST, remove the front drive pinion rear tapered roller bearing from the transaxle case.

    SST
    09612-65014   (09612-01040)

  1. Remove transaxle case plate No. 1 from the transaxle case.


70. REMOVE COUNTER DRIVE GEAR BEARING

D025049
  1. Remove the 2 counter drive gear bearing inner races RH from the transaxle case.

  1. Using SST, remove the counter drive gear bearing LH outer race from the transaxle case.

    SST
    09308-00010  

  1. D025050
    Using SST, remove the counter drive gear bearing rear outer race from the transaxle case.
    SST
    09308-00010  


71. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING

C067955
  1. Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.


72. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C067953
  1. Using a screwdriver, remove the oil seal from the transaxle case.


73. REMOVE FRONT TRANSAXLE CASE OIL SEAL

C067942E01
  1. Using SST and a hammer, remove the oil seal from the transaxle case.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07100)


74. REMOVE TRANSAXLE CASE OIL SEAL

C067941E01
  1. Using SST and a hammer, remove the transaxle case oil seal from the transaxle housing.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07100)

← COMPONENTS (from Aug 2005)INSPECTION (from Aug 2005) →