2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Nov 2005

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.


1. INSTALL REAR SEAT SHOULDER BELT COVER

  1. B114466
    Engage the 2 claws and install the rear seat shoulder belt cover.


2. INSTALL ROOF HEADLINING ASSEMBLY

  1. B114465
    Install the roof headlining with the clip.


3. INSTALL SEAT BELT ANCHOR COVER

  1. B114467
    Engage the 4 claws and install the seat belt anchor cover.


4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B114437E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15°or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45°or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat outer belt.

  1. B114551
    Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114463
    Install the bracket with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear center seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear center seat outer belt.

  1. B114461
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114469
    Engage the 2 claws and close the slip joint cover.

  1. B114459
    Install the 2 tongue plates.


5. INSTALL ROOF SIDE INNER GARNISH RH

  1. B114576E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.

  1. B114575
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.

  1. B114468
    Engage the 4 claws and install the center belt guide.


6. INSTALL ROOF SIDE INNER GARNISH LH

  1. B114578E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 5 clips and install the roof side inner garnish.

  1. B114577
    w/ Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 5 clips and install the roof side inner garnish.


7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

  1. B114573
    Engage the 3 clips and the 6 claws and install the deck trim side panel.

  1. Tighten the 3 screws.


8. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. B114574
    Connect the luggage compartment room light connector.

  1. Engage the 3 clips and the 6 claws and install the deck trim side board.

  1. Tighten the 3 screws.


9. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

  1. B130498
    Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114289
    Install the belt.


10. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


11. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

  1. B114431
    Install the rear door opening trim weatherstrip.


13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


14. INSTALL REAR DOOR SCUFF PLATE RH

  1. B114287
    Engage the 6 claws and install the rear door scuff plate.


15. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


16. INSTALL REAR SEAT ASSEMBLY RH

  1. B124326E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124299E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


17. INSTALL REAR SEAT ASSEMBLY LH

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


18. INSTALL NO. 1 REAR SEAT LEG COVER

  1. B124298
    Engage the 4 claws and install the rear seat No. 1 leg cover.


19. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


20. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


21. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


22. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


23. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


24. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138392
    Install the rear floor carpet.


25. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Nov 2005)COMPONENTS (from Jan 2006) →