REMOVAL
Removal / installation · Vehicles built from Nov 2005
- NOTICE:
- Always use "Torx" socket wrench E10 when removing the rear seat.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim) |
Remove the 2 package tray trim suspenders.

Remove the 5 pieces of hook tape.
Disengage the 2 claws and remove the package tray trim.
| 3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board) |
Release the 2 knobs and remove the deck board.

| 4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board) |
Remove the spare wheel cover.

| 5. REMOVE DECK FLOOR BOX RH (w/ Deck Board) |
Release the 2 knobs and remove the deck floor box.

| 6. REMOVE DECK FLOOR BOX LH (w/ Deck Board) |
- HINT:
- Use the same procedure as for the RH side.
| 7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) |
Remove the rear floor carpet.

| 8. REMOVE NO. 1 REAR SEAT LEG COVER |
Disengage the 4 claws and remove the No. 1 rear seat leg cover.

| 9. REMOVE NO. 2 REAR SEAT LEG COVER |
Disengage the 6 claws and remove the No. 2 rear seat leg cover.

| 10. REMOVE REAR SEAT ASSEMBLY RH |
Using "Torx" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.

Using "Torx" socket wrench E10, remove the 2 bolts and rear seat.

| 11. REMOVE REAR SEAT ASSEMBLY LH |
Using "Torx" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.

Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat.

| 12. REMOVE REAR DOOR SCUFF PLATE RH |
Disengage the 6 claws and remove the rear door scuff plate.

| 13. REMOVE REAR DOOR SCUFF PLATE LH |
- HINT:
- Use the same procedure as for the RH side.
| 14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Remove the rear door opening trim weatherstrip to the extent that the deck trim side panel and roof side inner garnish can be removed.

| 15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
- HINT:
- Use the same procedure as for the RH side.
| 16. REMOVE REAR DECK TRIM COVER |
for Grand Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
for Temper Spare Tire:

Using a clip remover, remove the 2 clips.
Disengage the 8 claws and remove the rear deck trim cover.
| 17. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH |
Remove the belt.

Remove the bolt.

Disengage the clip and remove the anchor plate.
| 18. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH |
- HINT:
- Use the same procedure as for the RH side.
| 19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
Remove the 3 screws.

Disengage the 3 clips and the 6 claws and remove the deck trim side panel.
| 20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Remove the 3 screws.

Disengage the 3 clips and the 6 claws and remove the deck trim side panel.
Disconnect the luggage compartment room light connector.
| 21. REMOVE ROOF SIDE INNER GARNISH RH |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the center belt guide.

w/ Curtain Shield Airbag:

- NOTICE:
- Replace the special clip with a new one when the roof side inner garnish is removed.
Disengage the 5 clips and remove the roof side inner garnish.
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
w/o Curtain Shield Airbag:

Disengage the 5 clips and remove the roof side inner garnish.
Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
| 22. REMOVE ROOF SIDE INNER GARNISH LH |
w/ Curtain Shield Airbag:

- NOTICE:
- Replace the special clip with a new one when the roof side inner garnish is removed.
Disengage the 5 clips and remove the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
w/o Curtain Shield Airbag:

Disengage the 5 clips and remove the roof side inner garnish.
Pass the rear seat outer belt through the slit in the roof side inner garnish.
| 23. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY |
Remove the 2 tongue plates.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and open the slip joint cover.

Remove the bolt and the through anchor.

Remove the bolt, the hook and the bracket.

Remove the bolt, the 2 hooks and the retractor.

| 24. REMOVE SEAT BELT ANCHOR COVER |
Using a moulding remover, disengage the 4 claws and remove the seat belt anchor cover.

| 25. REMOVE ROOF HEADLINING ASSEMBLY |
Using a clip remover, remove the clip and roof headlining.

| 26. REMOVE REAR SEAT SHOULDER BELT COVER |
Disengage the 2 claws and remove the rear seat shoulder belt cover.

