2005-2008 Yaris · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Nov 2005 – Dec 2005

Versions by build date: Nov 2005 – Dec 2005 from Jan 2006

CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.


1. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP (w/ Vertical Adjuster)

  1. B124377E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the vertical seat adjuster knob cap.


2. REMOVE VERTICAL SEAT ADJUSTER KNOB (w/ Vertical Adjuster)

  1. B124379
    Using "Torx" socket wrench T30, remove the bolt and the vertical seat adjuster knob.


3. REMOVE RECLINING ADJUSTER KNOB CAP

  1. B124380E01
    Using a screwdriver with its tip wrapped in protective tape, remove the reclining adjuster knob cap.


4. REMOVE RECLINING ADJUSTER RELEASE HANDLE

  1. B124382E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the reclining adjuster release handle.


5. REMOVE FRONT SEAT CUSHION OUTER SHIELD

  1. B124385
    Using "Torx" socket wrench T25, remove the screw.

  1. Disengage the 4 claws and remove the front seat cushion outer shield.


6. REMOVE FRONT SEAT INNER BELT ASSEMBLY

  1. B124389
    for Driver Side:

    1. Disengage the claw and remove the buckle switch connector.

    2. Using a clip remover, remove the 2 clamps.

    3. Remove the wire harness from the claw of the front seat frame adjuster.

    4. w/ Seat Heater System:

      1. Disconnect the seat heater connector.

  1. B124386
    for Front Passenger Side:

    1. Disengage the claw and remove the buckle switch connector.

    2. Disconnect the occupant detection sensor connector.

    3. Using a clip remover, remove the 2 clamps.

    4. Remove the wire harness from the claw of the front seat frame adjuster.

    5. w/ Seat Heater System:

      1. Disconnect the seat heater connector.

  1. B124387
    Remove the bolt and the front seat inner belt.


7. REMOVE FRONT SEAT CUSHION INNER SHIELD

  1. B124384
    Disengage the 2 claws and remove the front seat cushion inner shield.


8. REMOVE FRONT SEAT CUSHION COVER PAD

  1. B126903
    Disengage the 7 hooks.

  1. B126904
    for Driver Side:

    1. Remove the 3 bands.

    2. Disengage the 2 hooks and remove the front seat cushion cover pad.

  1. B126905
    for Front Passenger Side:

    1. Disengage the claw and connector.

    2. Remove the 3 bands.

    3. Disengage the 2 hooks and remove the front seat cushion cover pad.


9. REMOVE FRONT SEAT HEADREST SUPPORT

B126906

HINT:
Use the same procedure for both sides.

  1. Using a screwdriver, disengage the 2 claws and remove the front seat headrest support.


10. REMOVE FRONT SEATBACK COVER PAD

  1. B126908
    Remove the 2 pieces of hook tape.

  1. Disengage the 2 hooks and remove the front seatback cover pad.


11. REMOVE FRONT SEAT CUSHION LOWER OUTER SHIELD (w/ Vertical Adjuster)

  1. B126909
    Using "Torx" socket wrench T25, remove the screw.

  1. Disengage the claw and stud bolt and remove the front seat cushion lower outer shield.


12. REMOVE FRONT SEAT CUSHION LOWER INNER SHIELD (w/ Vertical Adjuster)

  1. B126910
    Using "Torx" socket wrench T25, remove the screw.

  1. Disengage the claw and stud bolt and remove the front seat cushion lower inner shield.

← REMOVAL (from Nov 2005)DISASSEMBLY (from Jan 2006) →