2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.


1. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH

  1. B127735
    for 6 Way Type:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.

  1. B127737
    for 4 Way Type:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.


2. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

  1. B127734
    for 6 Way Type:

    1. Engage the 2 claws and install the front seat cushion lower shield.

    2. Tighten the screw.

  1. B127736
    for 4 Way Type:

    1. Engage the claw and install the front seat cushion shield lower.

    2. Tighten the screw.


3. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH

  1. B114709
    Install the reclining adjuster outside cover with the screw.


4. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:
Use the same procedure as for the LH side.


5. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B127699
    for Full Memory Type:

    1. Engage the 2 claws and install the reclining adjuster inside cover.

    2. Tighten the screw.

  1. B114710
    for Normal Type:

    1. Engage the claw and install the reclining adjuster inside cover.

    2. Tighten the screw.


6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure as for the LH side.


7. INSTALL VERTICAL ADJUSTER SPACER (for Driver Side)

  1. B119878
    Engage the claw and install the vertical adjuster spacer.


8. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

  1. B114708
    Install the front seat side airbag with the 2 nuts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }

  1. B114707
    Install the 2 wire harness clamps.

  1. B119877
    Install the 3 wire harness clamps and the airbag connector.


9. INSTALL FRONT SEATBACK COVER PAD

B114713
  1. Install the front seatback cover pad.

    NOTICE:
    The fabrc for fixing the airbag must mot be wrinkled when installing the front seat back cover pad (w/ Front Seat Side Airbag).

  1. B114714E01
    Using hog ring pliers, install 3 new hog rings as shown in the illustration.


10. INSTALL FRONT SEAT HEADREST SUPPORT

B114715E03

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seat adjuster frame.

  1. Engage the 2 claws and install the front seat headrest support.


11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL (for Walk in Seat Type)

  1. B121715
    Engage the 4 claws and install the reclining remote control lever bezel.


12. INSTALL RECLINING REMOTE CONTROL LEVER (for Walk in Seat Type)

  1. B121733
    Engage the claw and install the reclining remote control lever.


13. INSTALL FRONT SEAT CUSHION COVER PAD

B119876
  1. w/ Seat Heater System:

    1. Engage the 2 claws and the 3 hooks and install the front seat cushion cover pad.

    2. Connect the seat heater connector.

    3. Engage the 3 hooks.

  1. w/o Seat Heater System:

    1. Engage the 2 claws and the 6 hooks and install the front seat cushion cover pad.

  1. for Front Passenger Side:

    1. Install the occupant detection sensor connector.

  1. B114700E01
    w/ Front Seat Side Airbag:

    1. Fix the front seat side airbag wire harness with the front seat cushion cover pad fixing cover.

  1. for Clip Type:

    1. Install the 2 clips.

  1. for J Hook Type:

    1. Engage the 2 hooks.

  1. B119875
    Install the front seatback cover band.


14. INSTALL FRONT SEAT CUSHION SHIELD RH

  1. B114698
    Engage the claw and the clip and install the front seat cushion shield.

  1. Tighten the screw.


15. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B114767E01
    for Driver Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.

    3. B127001
      Install the 4 clamps.

    4. Install the buckle switch connector.

    5. w/ Seat Heater System:

      1. Connect the seat heater connector.

    6. Engage the 2 hooks and install the front seat cushion cover.

  1. B114763E01
    for Front Passenger Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.

    3. B127000
      Install the 5 clamps.

    4. Install the buckle switch connector.

    5. Connect the occupant detection sensor connector.

    6. w/ Seat Heater System:

      1. Connect the seat heater connector.

    7. Engage the 2 hooks and install the front seat cushion cover.


16. INSTALL FRONT SEAT CUSHION SHIELD LH

  1. B114697
    Engage the 2 claws and the clip and install the front seat cushion shield.

  1. Tighten the screw.


17. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B114716
    Engage the claw and install the reclining adjuster release handle.


18. INSTALL VERTICAL ADJUSTER HANDLE (for Driver Side)

  1. B119874
    Install the vertical adjuster handle with the 2 screws.


19. INSTALL VERTICAL ADJUSTER COVER (for Driver Side)

  1. B119881
    Engage the 3 claws and install the vertical adjuster cover.

← DISASSEMBLY (from Aug 2005)INSTALLATION (from Aug 2005) →