DISASSEMBLY
Removal / installation · Vehicles built from Aug 2005
- CAUTION:
- Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.
- HINT:
- The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.
| 1. REMOVE VERTICAL ADJUSTER COVER (for Driver Side) |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the vertical adjuster cover.

| 2. REMOVE VERTICAL ADJUSTER HANDLE (for Driver Side) |
Remove the 2 screws and the vertical adjuster handle.

| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the reclining adjuster release handle.

| 4. REMOVE FRONT SEAT CUSHION SHIELD LH |
Remove the screw.

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and the clip and remove the front seat cushion shield.
| 5. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
for Drive Side:

Disengage the 2 hooks and remove the front seat cushion cover.
Remove the buckle switch connector.
w/ Seat Heater System:
- Disconnect the seat heater connector.
- Disconnect the seat heater connector.
Remove the 4 clamps.
Remove the wire harness from the claw of the front seat cushion shield.

Remove the bolt and the front seat inner belt.
for Front Passenger Side:

Disengage the 2 hooks and remove the front seat cushion cover.
Disconnect the occupant detection sensor connector.
w/ Seat Heater System:
- Disconnect the seat heater connector.
- Disconnect the seat heater connector.
Remove the buckle switch connector.
Remove the 5 clamps.
Remove the wire harness from the claw of the front seat cushion shield.

Remove the bolt and the front seat inner belt.
| 6. REMOVE FRONT SEAT CUSHION SHIELD RH |
Remove the screw.

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and the clip and remove the front seat cushion shield.
| 7. REMOVE FRONT SEAT CUSHION COVER PAD |
Remove the front seatback cover band.

for Clip Type:

Using a clip remover, remove the 2 clips.
for J Hook Type:
Disengage the 2 hooks.
w/ Front Seat Side Airbag:
Remove the hook tape and the front seat cushion cover pad fixing cover.
for Front Passenger side:

Remove the occupant detection sensor connector.
w/ Seat Heater System:
Disengage the 3 hooks.
Disconnect the seat heater connector.
Disengage the 2 claws and the 3 hooks and remove the front seat cushion cover pad.
w/o Seat Heater System:
Disengage the 2 claws and the 6 hooks and remove the front seat cushion cover pad.
| 8. REMOVE FRONT SEAT HEADREST SUPPORT |
Remove the 3 hog rings as shown in the illustration.

Disengage the 2 claws and remove the front seat headrest support.

- HINT:
- Use the same procedure for both sides.
| 9. REMOVE RECLINING REMOTE CONTROL LEVER (for Walk in Seat Type) |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the reclining remote control lever.

| 10. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL (for Walk in Seat Type) |
Disengage the 4 claws and remove the reclining remote control lever bezel.

| 11. REMOVE FRONT SEATBACK COVER PAD |
Remove the front seatback cover pad.

| 12. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) |
Remove the airbag connector and the 3 wire harness clamps.

Using a clip remover, remove the 2 wire harness clamps.

Remove the 2 nuts and the front seat side airbag.

| 13. REMOVE VERTICAL ADJUSTER SPACER (for Driver Side) |
Disengage the claw and remove the vertical adjuster spacer.

| 14. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
for Full Memory Type:

Remove the screw.
Disengage the 2 claws and remove the reclining adjuster inside cover.
for Normal Type:

Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover.
| 15. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
- HINT:
- Use the same procedure as for the LH side.
| 16. REMOVE RECLINING ADJUSTER OUTSIDE COVER LH |
Remove the screw and the reclining adjuster outside cover.

| 17. REMOVE RECLINING ADJUSTER OUTSIDE COVER RH |
- HINT:
- Use the same procedure as for the LH side.
| 18. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
for 6 Way Type:

Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
for 4 Way Type:

Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
| 19. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
for 6 Way Type:

Remove the screw.
Disengage the 2 claws and remove the front seat cushion lower shield.
for 4 Way Type:

Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
