2005-2008 Yaris · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands.


1. INSTALL REAR SEAT TRACK ASSEMBLY LH

  1. B114757
    Install the rear seat track with the 2 nuts.

    Torque:
    33 N*m{ 335 kgf*cm , 24 ft.*lbf }


2. INSTALL REAR SEAT TRACK ASSEMBLY RH

  1. B114756
    Install the rear seat track with the 3 nuts.

    Torque:
    33 N*m{ 335 kgf*cm , 24 ft.*lbf }


3. INSTALL REAR SEAT SLIDE CONTROL CABLE

  1. B114755
    Install the 4 clips.

  1. B127715E01
    Install the rear seat slide control cable as shown in the illustration.


4. INSTALL REAR SEAT RECLINING CONTROL CABLE

  1. B127714E01
    Install the rear seat reclining control cable as shown in the illustration.


5. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B114752
    Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.


6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure as for the LH side.


7. INSTALL REAR SEAT RECLINING INSIDE COVER

  1. B117767
    Engage the 2 claws and install the rear seat reclining inside cover.


8. INSTALL REAR SEAT RECLINING OUTSIDE COVER LH

  1. B117766
    Install the rear seat reclining outside cover with the screw.


9. INSTALL REAR SEAT RECLINING OUTSIDE COVER RH

  1. B117765
    Install the rear seat reclining outside cover with the 2 screws.


10. INSTALL REAR SEAT UNDER TRAY COVER

  1. B114751
    Install the rear seat under tray cover with the 6 clips.


11. INSTALL REAR SEATBACK COVER PAD SUB-ASSEMBLY

  1. B114750
    Install the rear seatback cover pad.

  1. B127656
    for 3 Point Type Rear Center Seat Belt:

    1. Install the rear seat belt hook with the bolt.

      Torque:
      5.0 N*m{ 50 kgf*cm , 44 in.*lbf }

  1. Fasten the 2 zippers.

  1. B114747E02
    Using hog ring pliers, install 7 new hog rings.

  1. B114745
    Install the 2 rear seatback bands.

  1. B126925
    w/ Tether Anchor Cover:

    HINT:
    Use the same procedure for both sides.


    1. Install the tether anchor covers with the screw.

    2. B126924
      Engage the 2 claws and close the cover.


12. INSTALL REAR SEAT HEADREST SUPPORT

  1. B114749E03
    Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. w/ Rear Center Seat Headrest:

    HINT:
    Use the same procedure to install all the rear seat headrest supports.


    1. Engage the 2 claws and install the rear seat headrest support.

  1. w/o Rear Center Seat Headrest:

    HINT:
    Use the same procedure to install all the rear seat headrest supports.


    1. Engage the 2 claws and install the rear seat headrest support.


13. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

  1. B117764
    Connect the rear seat reclining control cable and the rear seat slide control cable, and then install the rear seat lock control lever.

  1. Tighten the 2 screws.


14. INSTALL REAR SEAT LOCK STRIKER COVER

  1. B117768
    Engage the 2 claws and install the rear seat lock striker cover.


15. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Rear Center Seat Headrest)

  1. B114744E01
    Push in the lock button of the rear seat headrest support and install the rear center seat headrest.


16. INSTALL REAR SEAT HEADREST ASSEMBLY

  1. B117762E01
    Push in the lock button of the rear seat headrest support and install the rear seat headrest.


17. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY

  1. B114743E01
    Engage the 7 hooks and install the rear seat cushion cover pad.

  1. Using hog ring pliers, install 7 new hog rings.


18. INSTALL REAR SEAT CUSHION ASSEMBLY

  1. B114741
    Install the rear seat cushion with the 2 nuts.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

  1. Install the spacer into the bolt.

  1. Using "Torx" socket wrench T45, tighten the bolt.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }


19. INSTALL REAR SEAT SIDE HINGE COVER

  1. B117761
    Engage the 4 claws and install the rear seat side hinge cover.


20. INSTALL REAR SEAT INNER BELT ASSEMBLY

  1. B114648E01
    Install the rear seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex area of the rear seat back frame.

  1. Install the belt into the band.


21. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY LH

  1. B114652E01
    Install the rear seat inner belt with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the anchor plate over the convex areas of the rear seat back frame.

  1. Install the belt into the band.


22. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY RH

  1. B114655E01
    for 3 Point type Rear Center Seat Belt:

    1. Install the rear center seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the anchor plate over the convex area of the rear seat back frame.

  1. B117736E01
    for 2 Point type Rear Center Seat Belt:

    1. Install the rear center seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the anchor plate over the convex area of the rear seat frame adjuster.

  1. Install the tongue plate.

← DISASSEMBLY (from Aug 2005)INSTALLATION (from Aug 2005) →