2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

  1. B114426E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the front seat outer belt.

  1. B114423E01
    Hook the lower stay of the retractor onto the 2 body hooks and provisionally install the retractor with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf } for bolt A
    42 N*m{ 430 kgf*cm , 31 ft.*lbf } for bolt B

  1. B114479
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the front seat outer belt.

  1. B114497
    Install the anchor plate with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114496
    Install the anchor plate cover.

  1. B114427E01
    Connect the pretensioner connector.

    1. Connect the pretensioner connector.

    2. Lock the locking button.

      NOTICE:
      Securely lock the locking button.


2. INSTALL SEAT BELT ANCHOR COVER CAP

  1. B114478
    Engage the 3 claws and install the seat belt anchor cover cap.


3. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

  1. B114499
    Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.


4. INSTALL REAR SEAT OUTER BELT ASSEMBLY

  1. B114498
    Install the belt.


5. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

  1. B114477
    Install the front door opening trim weatherstrip.


6. INSTALL FRONT DOOR SCUFF PLATE

  1. B114494
    Engage the 8 claws and install the front door scuff plate.


7. INSTALL REAR SEAT BACK ASSEMBLY

  1. B106500E01
    Insert the 2 location pins through the 2 body holes and install the rear seat back.

  1. Using "Torx" socket wrench E10, tighten the 4 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


8. INSTALL REAR SEAT CUSHION COVER PAD

  1. B117758
    Pass the rear seat inner belt through the slit in the rear seat cushion.

  1. Engage the 3 hooks and install the rear seat cushion.

    NOTICE:
    Make sure that the rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.


9. INSTALL DECK FLOOR BOX RH

  1. B106446
    Set the deck floor box and lock the 2 knobs.

    HINT:
    Install the deck floor box LH when installing the LH side.


10. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


11. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


12. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


14. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2005)DISPOSAL (from Aug 2005) →