2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2005

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL SEAT BELT HOLE SEAL

  1. B114436
    Engage the 2 claws and install the seat belt hole seal.


2. INSTALL REAR SEAT OUTER BELT ASSEMBLY

  1. B114437E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat outer belt.

  1. B114483
    Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. B114482
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.


3. INSTALL ROOF SIDE INNER GARNISH

  1. B173323E01
    for RH Side (w/ Curtain Shield Airbag):

    1. Install a new special clip.

    2. Pass the rear seat outer and rear center seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B173324
    for RH Side (w/o Curtain Shield Airbag):

    1. Pass the rear seat outer and rear center seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114506E01
    for LH Side (w/ Curtain Shield Airbag):

    1. Install a new special clip.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. for LH Side (w/o Curtain Shield Airbag):

    1. B114507
      Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY

  1. B114501
    for RH Side:

    1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

    2. Tighten the 3 screws.

  1. B114502
    for LH Side:

    1. Connect the luggage compartment room light connector.

    2. Engage the 3 clips and the 3 claws and install the deck trim side panel.

    3. Tighten the 3 screws.

  1. B114500
    Engage the clip and install the anchor plate of the rear seat outer belt.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


5. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

  1. B114499
    Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.


7. INSTALL REAR SEAT SHOULDER BELT HANGER

  1. B117737
    Engage the 2 claws and install the rear seat shoulder belt hanger.

  1. B114498
    Install the belt of the rear seat outer belt.


8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

  1. B114546E01
    Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Yellow
    LH side
    White


9. INSTALL FRONT DOOR SCUFF PLATE

  1. B114494
    Engage the 8 claws and install the front door scuff plate.


10. INSTALL REAR SEAT BACK ASSEMBLY

  1. B106500E01
    Insert the 2 location pins through the 2 body holes and install the rear seat back.

  1. Using "Torx" socket wrench E10, tighten the 4 bolts.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


11. INSTALL REAR SEAT CUSHION COVER PAD

  1. B117758
    Pass the rear seat inner belt through the slit in the rear seat cushion.

  1. Engage the 3 hooks and install the rear seat cushion.

    NOTICE:
    Make sure that the rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.


12. INSTALL DECK FLOOR BOX RH

  1. B106446
    Set the deck floor box and lock the 2 knobs.


13. INSTALL DECK FLOOR BOX LH

HINT:
Use the same procedure as for the RH side.


14. INSTALL DECK BOARD SUB-ASSEMBLY

  1. B106447
    Set the deck board and lock the 2 knobs.


15. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for LH Side)

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Aug 2005)COMPONENTS (from Nov 2005) →