2005-2008 Yaris · Service Manual STEERING

C1524/24 Motor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The power steering ECU supplies the current to the power steering motor through the motor circuit.
DTC No.
DTC Detection Condition
Trouble Area
C1524/24
Short (or open) in motor circuit or abnormal voltage or current in motor circuit.
  1. Steering column assembly
  2. Power steering ECU

WIRING DIAGRAM

C117915E01

INSPECTION PROCEDURE


1. READ VALUE OF DATA LIST (MOTOR ACTUAL CURRENT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the items [Motor Actual Current] and [Command Value Current] in the DATA LIST and read the value displayed on the intelligent tester.

    Standard current:
    Data List Item
    Steering Position
    (Left Turned)
    Steering Position
    (Center)
    Steering Position
    (Right Turned)
    Motor Actual Current
    10 A to 55 A
    -1 A to +1 A
    -55 A to -10 A
    Command Value Current
    55 A
    0 A
    -55 A

    HINT:
    The current changes when steering wheel is turned.



OK
CHECK INTERMITTENT PROBLEMS
NG


2. INSPECT POWER STEERING ECU
F046434E01
  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    (Steering Position)
    Specified Condition
    M1 (b1-1) - PGND (A19-2)
    Turned to right
    1. Below 1 V (LHD)
    2. 10 to 16 V (RHD)
    M1 (b1-1) - PGND (A19-2)
    Turned to left
    1. 10 to 16 V (LHD)
    2. Below 1 V (RHD)
    M2 (b1-2) - PGND (A19-2)
    Turned to right
    1. 10 to 16 V (LHD)
    2. Below 1 V (RHD)
    M2 (b1-2) - PGND (A19-2)
    Turned to left
    1. Below 1 V (LHD)
    2. 10 to 16 V (RHD)



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BODY GROUND)
F046438E01
  1. Disconnect the connector from the power steering ECU.

  1. Measure the voltage and the resistance.

Standard:
Tester Connection
Condition
Specified Condition
PGND (A19-2) - Body ground
Always
Below 1 Ω
PIG (A19-1) - Body ground
Ignition switch on (IG).
10 to 16 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT STEERING COLUMN ASSEMBLY (POWER STEERING MOTOR)
F046435E01
  1. Disconnect the connector from the power steering ECU.

  1. Measure the resistance.

Standard resistance:
Tester Connection
Condition
Specified Condition
M1 (b1-1) - M2 (b1-2)
Always
0.08 to 0.15 Ω
M1 (b1-1) - Body ground
Always
1 MΩ or higher
M2 (b1-2) - Body ground
Always
1 MΩ or higher



NG
REPLACE STEERING COLUMN ASSEMBLY
OK

REPLACE POWER STEERING ECU


← C1516/16 Torque Sensor Zero Point Adjustment Incomplete (from Aug 2005)C1531/31 EPS ECU Circuit Malfunction (+ C1532/32, C1533/33, C1534/34) (Aug 2005 – Dec 2005) →