INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL REAR COIL SPRING LH |
Install the coil spring insulator lower onto the axle beam.
Install the coil spring insulator upper so that its gap fits onto the end of coil spring.

Install the coil spring onto the axle beam.

- NOTICE:
- The paint mark of the coil spring should be towards the underside and rear side of the vehicle.
| 2. INSTALL REAR COIL SPRING RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 3. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH |
![]() ![]() |
Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.
Jack up the axle beam slowly, and provisionally install the shock absorber (lower side) with the bolt and nut onto the axle beam.
Install the suspension support and cushion retainer.
While holding the piston rod, install a new nut (lower nut) to the specified standard.

- Standard:
- 15 to 18 mm (0.591 to 0.709 in.)
While holding the piston rod, tighten a new nut (upper nut).

- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
| 4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 5. INSTALL REAR SHOCK ABSORBER CAP LH |
| 6. INSTALL REAR SHOCK ABSORBER CAP RH |
| 7. INSTALL REAR ABSORBER CAP |
| 8. INSTALL REAR ABSORBER CAP |
| 9. INSTALL REAR LH FLEXIBLE HOSE |
![]() ![]() |
Connect the flexible hose onto the axle beam with a new clip.
Using SST, install the brake tube.
- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 10. INSTALL REAR RH FLEXIBLE HOSE |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 11. INSTALL SKID CONTROL SENSOR WIRE |
![]() ![]() |
Install the skid control sensor wire onto the axle beam with the nut.
- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Connect the skid control sensor wire connector.

| 12. INSTALL REAR WHEEL |
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 13. STABILIZE SUSPENSION |
Lower the vehicle from the jack.
Bounce the vehicle up and down several times to stabilize the suspension.
| 14. FULLY TIGHTEN REAR AXLE BEAM |
![]() ![]() |
Suspend the jack on the rear axle spring seat and adjust the length of the shock absorber to the reference value.
- Length of shock absorber:
- 220 mm (8.7 in.)
Fully tighten the 2 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
| 15. FULLY TIGHTEN REAR SHOCK ABSORBER LH |
Fully tighten the shock absorber (lower side) with the bolt.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| 16. FULLY TIGHTEN REAR SHOCK ABSORBER RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 18. FILL RESERVOIR WITH BRAKE FLUID |
![]() ![]() |
LHD:
Disengage the 3 clips and separate the hood to cowl top seal.
Remove the cowl top ventilator louver.
RHD:
Disengage the 2 clips and separate the hood to cowl top seal.
Remove the cowl top ventilator louver.
Set the brake fluid can upside down on the reservoir.

- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
- SAE J1704 or FMVSS No. 116 DOT4
| 19. BLEED MASTER CYLINDER |
- HINT:
- If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.
Using SST, disconnect the brake tubes from the master cylinder.

- SST
- 09023-00100
Slowly depress the brake pedal and hold it there (Step A).

Block the outer holes with your fingers, and release the brake pedal (Step B).

Repeat steps A and B 3 or 4 times.
Using SST, connect the brake tubes to the master cylinder.

- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 20. BLEED BRAKE LINE |
![]() ![]() |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).
Repeat steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc and Rear Drum Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Disc Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 21. BLEED BRAKE ACTUATOR (w/ VSC) |
- NOTICE:
- After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.
Depress the brake pedal more than 20 times with the engine off.
Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).

- NOTICE:
- Do not start the engine.
Select AIR BLEEDING on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).
Repeat steps E and F until all air in the fluid is completely bled out.
Tighten the bleeder plug completely.
- Torque:
- Front Disc and Rear Drum Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Disc Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for each wheel to bleed the air out of the brake line.
Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator to bleed the air using the intelligent tester (Step G).
- NOTICE:
- Release the brake pedal at this time.
- HINT:
- This operation stops automatically after 4 seconds.
Check if the operation has stopped by referring to the intelligent tester display (Step H).
Repeat step G and H until all air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc and Rear Drum Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Disc Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the the intelligent tester.
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (Step I).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there.
- NOTICE:
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- HINT:
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
- When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
Tighten the bleeder plug, then release the brake pedal (Step J).
Repeat step I and J until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc and Rear Drum Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Disc Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty of brake fluid.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step K).

When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step L).
Repeat steps K and L until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Disc and Rear Drum Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Disc Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Make sure that the air bleeding is complete by referring to the intelligent tester display.
| 22. CHECK FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
- SAE J1704 or FMVSS No. 116 DOT4
| 23. CHECK FOR BRAKE FLUID LEAKAGE |
| 24. INSPECT REAR WHEEL ALIGNMENT |
| 25. CHECK ABS SENSOR SIGNAL (w/o VSC) |
| 26. CHECK VSC SENSOR SIGNAL (w/ VSC) |





