2005-2008 Yaris · Service Manual BRAKE

TEST MODE PROCEDURE

Troubleshooting · Vehicles built from Aug 2005

HINT:
  1. By switching the skid control ECU from normal mode to test mode, abnormality detection sensitivity is enhanced and troubleshooting can be conducted efficiently.
  2. Perform a sensor check in test mode after the speed sensor or sensor rotor has been repaired or replaced.
  3. If the ignition switch is turned from on to ACC or off during test mode, DTCs related to the signal check function will be erased.
  4. During test mode, the skid control ECU stores all DTCs related to the signal check function, and the DTCs are erased if normality is confirmed. Any remaining DTCs are those indicating abnormalities that were found.


TEST MODE (SIGNAL CHECK) PROCEDURE (USING INTELLIGENT TESTER)
  1. Turn the ignition switch off.

  2. Check that the steering wheel is in the straight-ahead position.

  3. A/T: Check that the shift lever is in the P position and apply the parking brake.

  4. M/T: Check that the shift lever is in neutral and apply the parking brake.

  5. A107926E08
    Connect the intelligent tester to the DLC3.

  6. Turn the ignition switch on (IG).

  7. Turn the tester on.

  8. Switch the skid control ECU to test mode using the intelligent tester.
    Select the following menu items: Chassis / ABS/VSC/TRC / Utility / Signal Check.

  9. BR03904E22
    Check that the ABS warning light and VSC warning light blink as shown in the illustration.

  10. Start the engine.


DECELERATION SENSOR CHECK (USING INTELLIGENT TESTER)
  1. Keep the vehicle stationary on a level surface for 1 second or more.

    HINT:
    The deceleration sensor check can be performed together with the following master cylinder pressure sensor check.


MASTER CYLINDER PRESSURE SENSOR CHECK (USING INTELLIGENT TESTER)
  1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.

  2. Check that the ABS warning light remains illuminated for 3 seconds.

    HINT:
    1. Ensure that the ABS warning light comes on.
    2. While the ABS warning light remains illuminated, continue depressing the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
    3. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.


SPEED SENSOR CHECK (USING INTELLIGENT TESTER)

  1. BR03904E22
    Check that the ABS warning light is blinking as shown in the illustration.

  2. Check the speed sensor signal.

    1. Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds.

    2. Check that the ABS warning light goes off.

      HINT:
      1. The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
      2. If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
      3. The ABS warning light comes on immediately when an abnormality is detected.
      4. When the speed sensor signal is normal, the ABS warning light goes off while driving at 45 km/h (28 mph) or more and blinks in the test mode pattern while stationary.
      5. Do not drive the vehicle at a speed of 80 km/h (50 mph) or more after the ABS warning light turns off, because test mode DTC are set again when the vehicle speed exceeds 80 km/h (50 mph).

      C115115E02

    3. Stop the vehicle.


YAW RATE SENSOR CHECK (USING INTELLIGENT TESTER)

  1. BR03904E22
    Check that the VSC warning light is blinking as shown in the illustration.

  2. Keep the vehicle stationary on a level surface for 1 second or more.

  3. F002135E01
    Shift the shift lever to the D position (A/T) and drive the vehicle at a speed of approximately 6 km/h (4 mph), and turn the steering wheel either to the left or right 90° or more to turn the vehicle through 180 degrees.

  4. A/T: Stop the vehicle, move the shift lever into the P position, and then apply the parking brake.

  5. M/T: Stop the vehicle, move the shift lever into neutral, and then apply the parking brake.

  6. Check that the skid control buzzer sounds for 3 seconds.

    HINT:
    1. If the skid control buzzer sounds, the signal check has been completed normally.
    2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here).
    3. If the skid control buzzer still does not sound, there is a malfunction in the yaw rate sensor, so check for DTCs.
    4. Drive the vehicle in a 180° semi circle. At the end of the turn, the direction of the vehicle should be within 180° +-5° of its start position.
    5. Complete the vehicle turn within 20 seconds.
    6. Do not spin the wheels.


END OF SENSOR CHECK (USING INTELLIGENT TESTER)
  1. When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.

    NOTICE:
    If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.


READ SIGNAL CHECK FUNCTION DTCs (USING INTELLIGENT TESTER)
  1. Read the DTC(s) by following the instructions on the tester screen.


TEST MODE (SIGNAL CHECK) PROCEDURE (USING SST CHECK WIRE)
  1. Turn the ignition switch off.

  2. Check that the steering wheel is in the straight-ahead position.

  3. A/T: Check that the shift lever is in the P position and apply the parking brake.

  4. M/T: Check that the shift lever is in neutral and apply the parking brake.

  5. F100115E01
    Using SST, connect terminals TS and CG of the DLC3.
    SST
    09843-18040  

  6. Turn the ignition switch on (IG).

  7. BR03904E22
    Check that the ABS warning light and VSC warning light blink as shown in the illustration.

  8. Start the engine.


DECELERATION SENSOR CHECK (USING SST CHECK WIRE)
  1. Keep the vehicle stationary on a level surface for 1 second or more.

    HINT:
    The deceleration sensor check can be performed together with the following master cylinder pressure sensor check.


MASTER CYLINDER PRESSURE SENSOR CHECK (USING SST CHECK WIRE)
  1. Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.

  2. Check that the ABS warning light remains illuminated for 3 seconds.

    HINT:
    1. Ensure that the ABS warning light comes on.
    2. While the ABS warning light remains illuminated, continue depressing the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
    3. The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.


SPEED SENSOR CHECK (USING SST CHECK WIRE)

  1. BR03904E22
    Check that the ABS warning light blinks as shown in the illustration.

  2. Check the speed sensor signal.

    1. Drive the vehicle straight forward at a speed of 45 km/h (28 mph) or more for several seconds, and then step on the brake pedal.

    2. Check that the ABS warning light goes off.

      HINT:
      1. The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
      2. If the speed sensor check is commenced while the steering wheel is turned, the ABS warning light may come on after the low speed check is finished.
      3. The ABS warning light comes on immediately when an abnormality is detected.
      4. When the speed sensor signal is normal, the ABS warning light goes off while driving at 45 km/h (28 mph) or more and blinks in the test mode pattern while stationary.
      5. Do not drive the vehicle at a speed of 80 km/h (50 mph) or more after the ABS warning light turns off, because test mode DTC are set again when the vehicle speed exceeds 80 km/h (50 mph).

      C115115E02

    3. Stop the vehicle.


YAW RATE SENSOR CHECK (USING SST CHECK WIRE)

  1. BR03904E22
    Check that the VSC warning light blinks as shown in the illustration.

  2. Keep the vehicle stationary on a level surface for 1 second or more.

  3. F002135E01
    Shift the shift lever to the D position (A/T) and drive the vehicle at a speed of approximately 6 km/h (4 mph), and turn the steering wheel either to the left or right 90° or more to turn the vehicle through 180 degrees.

  4. A/T: Stop the vehicle, move the shift lever into the P position, and then apply the parking brake.

  5. M/T: Stop the vehicle, move the shift lever into neutral, and then apply the parking brake.

  6. Check that the skid control buzzer sounds for 3 seconds.

    HINT:
    1. If the skid control buzzer sounds, the signal check has been completed normally.
    2. If the skid control buzzer does not sound, check the skid control buzzer circuit (Click here).
    3. If the skid control buzzer still does not sound, there is a malfunction in the yaw rate sensor, so check for DTCs.
    4. Drive the vehicle in a 180° semi circle. At the end of the turn, the direction of the vehicle should be within 180° +-5° of its start position.
    5. Complete the vehicle turn within 20 seconds.
    6. Do not spin the wheels.


END OF SENSOR CHECK (USING SST CHECK WIRE)
  1. When the sensor check is successfully completed, the ABS warning light blinks in the test mode pattern when the vehicle is stopped, and goes off when the vehicle is driven.

    NOTICE:
    If the sensor check is not completed, the ABS warning light blinks even while the vehicle is driving and the ABS does not operate.


READ SENSOR SIGNAL CHECK FUNCTION DTCs (USING SST CHECK WIRE)

  1. F100115E02
    Using SST, connect terminals TC and CG of the DLC3.
    SST
    09843-18040  

  2. Turn the ignition switch on.

  3. Read the number of blinks of the ABS warning light.

    HINT:
    BR03904E06
    If all sensors are normal, a normal system code is output (the light comes on for 0.25 seconds at intervals of 0.25 seconds).

  4. After the check, disconnect the SST from terminals TC and CG of the DLC3.

  5. Turn the ignition switch off.


SENSOR SIGNAL CHECK FUNCTION DTCs
ABS sensor: 
DTC No.
Diagnosis
Trouble Areas
C1271/71
Low output signal of front speed sensor RH
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
C1272/72
Low output signal of front speed sensor LH
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
C1273/73
Low output signal of rear speed sensor RH
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
C1274/74
Low output signal of rear speed sensor LH
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
C1275/75
Abnormal change in output signal of front speed sensor RH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1276/76
Abnormal change in output signal of front speed sensor LH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1277/77
Abnormal change in output signal of rear speed sensor RH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1278/78
Abnormal change in output signal of rear speed sensor LH
  1. Sensor installation
  2. Speed sensor rotor
  3. Foreign matter on sensor tip or sensor rotor
C1279/79
Deceleration sensor output voltage malfunction
  1. Yaw rate sensor
  2. Sensor installation
C1281/81
Master cylinder pressure sensor output malfunction
Master cylinder pressure sensor
VSC sensor: 
DTC No.
Diagnosis
Trouble Areas
C0371/71
Yaw rate sensor
Yaw rate sensor

HINT:
  1. The DTCs in this table are only output in test mode.
  2. Detection of DTCs from C1271/71 to C1274/74 is completed before the vehicle speed reaches 5 km/h (3 mph).
  3. Detection of DTCs from C1275/75 to C1278/78 is completed before the vehicle speed reaches 45 km/h (28 mph).
  4. C1271/71 - C1274/74: Speed output from only one wheel is extremely low despite other wheel speed outputs reaching 5 km/h (3 mph).

  5. F100272E01
    C1275/75 - C1278/78: Abnormal speed sensor output frequency is as shown in the illustration.

← CALIBRATION (from Aug 2005)PROBLEM SYMPTOMS TABLE (from Aug 2005) →