INSTALLATION
Removal / installation · Vehicles built from Jan 2006
| 1. INSTALL REAR COIL SPRING LH |
Install the coil spring insulator lower onto the axle beam.
Install the coil spring insulator upper so that its gap fits onto the end of coil spring.

Install the coil spring onto the axle beam.

- NOTICE:
- The paint mark of the coil spring should be towards the underside and rear side of the vehicle.
| 2. INSTALL REAR COIL SPRING RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 3. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH |
![]() ![]() |
Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.
Jack up the axle beam slowly, and provisionally install the shock absorber (lower side) with the bolt and nut onto the axle beam.
Install the suspension support and cushion retainer.
While holding the piston rod, install a new nut (lower nut) to the specified standard.

- Standard:
- 15 to 18 mm (0.591 to 0.709 in.)
While holding the piston rod, tighten a new nut (upper nut).

- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
| 4. TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 5. INSTALL REAR SHOCK ABSORBER CAP LH |
| 6. INSTALL REAR SHOCK ABSORBER CAP RH |
| 7. INSTALL REAR LH FLEXIBLE HOSE |
![]() ![]() |
Connect the flexible hose onto the axle beam with a new clip.
Using SST, install the brake tube.
- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 8. INSTALL REAR RH FLEXIBLE HOSE |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 9. INSTALL SKID CONTROL SENSOR WIRE (w/ ABS) |
![]() ![]() |
Install the skid control sensor wire onto the axle beam with the nut.
- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
Connect the skid control sensor wire connector.

| 10. INSTALL REAR WHEEL |
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 11. STABILIZE SUSPENSION |
Lower the vehicle from the jack.
Bounce the vehicle up and down several times to stabilize the suspension.
| 12. FULLY TIGHTEN REAR AXLE BEAM |
![]() ![]() |
Suspend the jack on the rear axle spring seat and adjust the length of the shock absorber to the reference value.
- Length of shock absorber:
- 220 mm (8.7 in.)
Fully tighten the 2 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
| 13. FULLY TIGHTEN REAR SHOCK ABSORBER LH |
Fully tighten the shock absorber (lower side) with the bolt.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
| 14. FULLY TIGHTEN REAR SHOCK ABSORBER RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 15. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) |
Engage the 3 hooks and install the rear seatback.

Tighten the 3 bolts.
- Torque:
- 7.9 N*m{ 80 kgf*cm , 70 in.*lbf }
Install the rear seat outer belt into the rear seat shoulder belt guide.

- HINT:
- Use the same procedure for both sides.
for 3 Point Type Rear Center Seat belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 16. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type) |
Pass the rear seat inner belt through the rear seat cushion cover pad slit.

Engage the 3 hooks and install the rear seat cushion cover pad.
- NOTICE:
- SE Make sure that the 2 rear seat cushion lock hooks and the rear seat cushion frame are securely engaged.
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 18. FILL RESERVOIR WITH BRAKE FLUID |
![]() ![]() |
Remove the cowl top No. 2 ventilator louver center.
Set the brake fluid can upside down on the reservoir.

- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
- SAE J1704 or FMVSS No. 116 DOT4
| 19. BLEED MASTER CYLINDER |
- HINT:
- If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.
Using SST, disconnect the brake tubes from the master cylinder.

- SST
- 09023-00100
Slowly depress the brake pedal and hold it there (Step A).

Block the outer holes with your fingers, and release the brake pedal (Step B).

Repeat steps A and B 3 or 4 times.
Using SST, connect the brake tubes to the master cylinder.

- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 20. BLEED BRAKE LINE |
![]() ![]() |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).
Repeat steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 21. CHECK FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
- SAE J1704 or FMVSS No. 116 DOT4
| 22. CHECK FOR BRAKE FLUID LEAKAGE |
| 23. INSPECT REAR WHEEL ALIGNMENT |
| 24. CHECK ABS SENSOR SIGNAL (w/ ABS) |






