2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSPECTION

Inspection · Vehicles built from Jan 2006


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    Destination
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    General
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    Australia
    175/65R14 82T
    185/60R15 84H
    Driving below 140 km/h (87 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 140 km/h (87 mph)
    260 (2.7, 38)
    260 (2.7, 38)
    G.C.C. Countries
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)

  1. R003031E01
    Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less


MEASURE VEHICLE HEIGHT

C132096E01

Vehicle height:
Destination
A-B
C-D
General
G.C.C. Countries
86 mm
(3.39 in.)
14 mm
(0.55 in.)
General
(Rough Road Package)
66 mm
(2.60 in.)
-4.0 mm
(-0.16 in.)
Australia
86 mm
(3.39 in.)
9.0 mm
(0.35 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of lower arm set front bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of axle beam set bolt center

NOTICE:
Before inspecting the wheel alignment, check the vehicle height.

HINT:
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.


INSPECT TOE-IN

SA03213E02

Toe-in:
Destination
Tire Size
A+B
C-D
General
G.C.C. Countries
175/65R14
0°16' +- 0°20'
(0.27° +- 0.33°)
2.7 +- 3.0 mm
(0.11 +- 0.12 in.)
185/60R15
0°16' +- 0°20'
(0.27° +- 0.33°)
2.8 +- 3.0 mm
(0.11 +- 0.12 in.)
General
(Rough Road Package)
175/65R14
0°12' +- 0°20'
(0.20° +- 0.33°)
2.0 +- 3.0 mm
(0.08 +- 0.12 in.)
185/60R15
0°12' +- 0°20'
(0.20° +- 0.33°)
2.1 +- 3.0 mm
(0.08 +- 0.12 in.)
Australia
175/65R14
0°15' +- 0°20'
(0.25° +- 0.33°)
2.5 +- 3.0mm
(0.10 +- 0.12 in.)
185/60R15
0°15' +- 0°20'
(0.25° +- 0.33°)
2.6 +- 3.0mm
(0.10 +- 0.12 in.)

HINT:
Only measure C-D when A+B can not be measured.


INSPECT CAMBER
  1. Install the camber-caster-kingpin gauge and position the rear wheel on the alignment tester.

  1. Inspect the camber.

    Camber:
    Destination
    Camber
    General
    G.C.C. Countries
    -0°56' +- 45'
    (-0.93° +- 0.75°)
    General
    (Rough Road Package)
    -0°54' +- 45'
    (-0.90° +- 0.75°)
    Australia
    -0°55' +- 45'
    (-0.92° +- 0.75°)

    NOTICE:
    The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both cambers.

    If the camber is not within the specified range, inspect the suspension parts and replace them if necessary.

← ADJUSTMENT (from Nov 2005)INSPECTION (from Nov 2006) →