2005-2008 Yaris · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE REAR WHEEL

3. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


4. SEPARATE SKID CONTROL SENSOR WIRE

C125279
  1. Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.

    NOTICE:
    Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.

  1. C107566
    Remove the nut and separate the skid control sensor wire.


5. SEPARATE REAR BRAKE NO. 4 TUBE (for Rear Drum Brake)

C107570E01
  1. Using SST, separate the brake tube from the flexible hose.

    SST
    09023-00100  

  1. Remove the clip and disconnect the flexible hose from the axle beam.

  1. Remove the nut and separate the brake tube.


6. SEPARATE REAR BRAKE NO. 3 TUBE (for Rear Drum Brake)

HINT:
The removal procedure for the RH side is the same as that for the LH side.


7. REMOVE REAR BRAKE NO. 4 TUBE (for Rear Disc Brake)

C107571E01
  1. Using SST, separate the brake tube from the flexible hose.

    SST
    09023-00100  

  1. Remove the 2 clips and disconnect the 2 flexible hoses from the axle beam.

  1. Remove the nut and remove the brake tube.


8. REMOVE REAR BRAKE NO. 3 TUBE (for Rear Disc Brake)

HINT:
The removal procedure for the RH side is the same as that for the LH side.


9. SEPARATE PARKING BRAKE NO. 3 CABLE ASSEMBLY

C126196
  1. Using pliers, pinch both ends of the claw of cable clamp and disengage the clamp.

  1. Remove the bolt and separate the parking brake cable.

  1. Remove the cable clamp from the parking brake cable.

    HINT:
    Replace the clamp with a new one when installing the parking brake cable.


10. SEPARATE PARKING BRAKE NO. 2 CABLE ASSEMBLY
  1. for Rear Drum Brake:

    HINT:
    The removal procedure for the RH side is the same as that for the LH side.

  1. for Rear Disc Brake:

    1. Remove the cable clamp from the axle beam.

      HINT:
      Break the cable clamp to remove it.

    2. Remove the bolt and separate the parking brake cable.

    3. Remove the cable clamp from the parking brake cable.

      HINT:
      Replace the clamp with a new one when reinstalling the parking brake cable.


11. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)
  1. Release the parking brake and remove the rear brake drum.
    If the rear brake drum cannot be removed easily, perform the following procedure.

  1. for Manual Transaxle:

    1. Remove the shift lever knob.

    2. Remove the shifting hole cover (Click here).

  1. Remove the console box rear cover (Click here).

  1. Remove the console box carpet (Click here).

  1. Remove the rear console box (Click here).

  1. C129772
    Loosen the wire adjusting nut.

    NOTICE:
    Do not reuse the loosened nut.

  1. C129773
    Remove the hole plug.

  1. C129774E01
    Insert SST through the hole in the backing plate, pull the parking brake shoe lever toward the rear of the vehicle and remove the rear brake drum.
    SST
    09921-00010  


12. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH (for Rear Disc Brake)

C130313
  1. Remove the 2 bolts and separate the disc brake caliper from the rear axle beam.

    NOTICE:
    Hang the caliper using a piece of string or the equivalent


13. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH (for Rear Disc Brake)

HINT:
The removal procedure for the RH side is the same as that for the LH side.


14. REMOVE REAR DISC (for Rear Disc Brake)

C108951E01
  1. Place matchmarks on the disc and axle hub and remove the disc.


15. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

C130314E01
  1. for Rear Drum Brake:

    1. Remove the 4 bolts and remove the axle hub and bearing from the axle beam.

      NOTICE:
      Suspend the backing plate with a piece of rope.

  1. for Rear Disc Brake:

    1. Remove the 4 bolts and remove the axle hub and bearing and the dust cover from the axle beam.


16. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


17. LOOSEN REAR AXLE BEAM

C112605E01
  1. Loosen the 2 bolts.

    NOTICE:
    Do not remove the bolts.


18. REMOVE REAR ABSORBER CAP

19. REMOVE REAR SHOCK ABSORBER CAP LH

20. REMOVE REAR SHOCK ABSORBER CAP RH

21. REMOVE REAR SHOCK ABSORBER LH
  1. Support the axle beam with a jack. Insert a wooden block between the jack and the rear axle spring seat to prevent damage.

  1. C106030
    Remove the 2 nuts while keeping the piston rod from rotating.

  1. Remove the cushion retainer and suspension support.

  1. C106031
    Remove the bolt while keeping the nut from rotating and remove the shock absorber.

    NOTICE:
    Remove the nut from the bolt side because the one on the lower side is a jam nut.


22. REMOVE REAR SHOCK ABSORBER RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


23. REMOVE REAR COIL SPRING LH
  1. Lower the jacks slowly.

  1. Remove the coil spring, coil spring insulator upper and coil spring insulator lower.


24. REMOVE REAR COIL SPRING RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.


25. REMOVE REAR AXLE BEAM

C112605E01
  1. Remove the 2 bolts and remove the axle beam.

← COMPONENTS (from Nov 2005)REPLACEMENT (from Nov 2005) →