B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2005
DESCRIPTION
The driver side - side airbag sensor consists of parts including the diagnostic circuit and the lateral deceleration sensor.When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1620/21 is set when a malfunction is detected in the driver side - side airbag sensor circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1620/21 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connector from the steering pad.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- HINT:
- Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.
- Disconnect the connector from the front passenger airbag assembly.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
- Disconnect the connector from the driver side knee airbag assembly.
| 1. CHECK DTC |
![]() ![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1620/21 is not output.
- HINT:
- DTCs other than DTC B1620/21 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly, driver side rear airbag sensor and the driver side - side airbag sensor.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK FLOOR WIRE (FOR OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor assembly and the driver side - side airbag sensor LH.
LHD (with curtain shield airbag):Using a service wire, connect J17-4 (BBL+) and J17-3 (BBL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
LHD (without curtain shield airbag):Using a service wire, connect J40-2 (BBL+) and J40-1 (BBL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
RHD (with curtain shield airbag):Using a service wire, connect J16-4 (BBR+) and J16-3 (BBR-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
RHD (without curtain shield airbag):Using a service wire, connect J39-2 (BBR+) and J39-1 (BBR-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J8-8 (BBD+) - J8-15 (BBD-)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK FLOOR WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J8-8 (BBD+) - J8-15 (BBD-)
Always
1 MΩ or Higher
|
|
||||
| OK | |
| 5. CHECK FLOOR WIRE (TO B+) |
![]() ![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
J8-8 (BBD+) - Body ground
Ignition switch on (IG)
Below 1 V
J8-15 (BBD-) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 6. CHECK FLOOR WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J8-8 (BBD+) - Body ground
Always
1 MΩ or Higher
J8-15 (BBD-) - Body ground
Always
1 MΩ or Higher
|
|
||||
| OK | |
| 7. CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
![]() ![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1620/21 is output. (with curtain shield airbag)
A
DTC B1620/21 is output. (without curtain shield airbag)
B
DTC B1625/22 is output.
C
Neither DTC B1620/21 nor B1625/22 is output.
D
|
|
||||
|
|
||||
|
|
||||
| D | ||
| ||
| 8. CHECK FLOOR WIRE (FOR OPEN) |
![]() ![]() |
Disconnect the connectors from the driver side - side airbag sensor and the driver side rear airbag sensor.
LHD:Using a service wire, connect J15-1 (BCL-) and J15-2 (BCL+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
RHD: Using a service wire, connect J14-1(BCR-) and J14-2 (BCR+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J17-1 (BCL+) - J17-2 (BCL-) (*1)
Always
Below 1 Ω
J16-1 (BCR+) - J16-2 (BCR-) (*2)
Always
Below 1 Ω
*2: RHD
|
|
||||
| OK | |
| 9. CHECK FLOOR WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J17-1 (BCL+) - J17-2 (BCL-) (*1)
Always
1 MΩ or Higher
J16-1 (BCR+) - J16-2 (BCR-) (*2)
Always
1 MΩ or Higher
*2: RHD
|
|
||||
| OK | |
| 10. CHECK FLOOR WIRE (TO B+) |
![]() ![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester Connection
Condition
Specified Condition
J17-1 (BCL+) - Body ground (*1)
Ignition switch on (IG)
Below 1 V
J17-2 (BCL-) - Body ground (*1)
Ignition switch on (IG)
Below 1 V
J16-1 (BCR+) - Body ground (*2)
Ignition switch on (IG)
Below 1 V
J16-2 (BCR-) - Body ground (*2)
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 11. CHECK FLOOR WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
J17-1 (BCL+) - Body ground (*1)
Always
1 MΩ or Higher
J17-2 (BCL-) - Body ground (*1)
Always
1 MΩ or Higher
J16-1 (BCR+) - Body ground (*2)
Always
1 MΩ or Higher
J16-1 (BCR-) - Body ground (*2)
Always
1 MΩ or Higher
|
|
||||
| OK | |
| 12. CHECK DRIVER SIDE REAR AIRBAG SENSOR |
![]() ![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the driver side rear airbag sensor with the front passenger side rear airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1620/21 is output.
A
DTC B1625/22 is output.
B
Neither DTC B1620/21 nor B1625/22 is output.
C
- HINT:
- DTCs other than B1620/21 and B1625/22 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | ||
| ||







