2005-2008 Yaris · Service Manual RESTRAINTS

B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The front passenger side - side airbag sensor consists of parts including the diagnostic circuit and the lateral deceleration sensor.
When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1625/22 is set when a malfunction is detected in the front passenger side - side airbag sensor circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1625/22
  1. Center airbag sensor assembly detects open circuit signal in front passenger side - side airbag sensor circuit for 2 seconds.
  2. Front passenger side - side airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor RH (Front passenger side - side airbag sensor) (LHD)
  3. Side airbag sensor LH (Front passenger side - side airbag sensor) (RHD)
  4. Center airbag sensor assembly

WIRING DIAGRAM

H102127E02

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connector from the steering pad.
  5. Disconnect the connector from the front seat outer belt assembly LH.
  6. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.

  7. Disconnect the connector from the front passenger airbag assembly.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.
  12. Disconnect the connector from the driver side knee airbag assembly.

1. CHECK DTC
H100844E04
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1625/22 is not output.

    HINT:
    DTCs other than DTC B1625/22 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor, front passenger side rear airbag sensor and the front passenger side - side airbag sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. CHECK FLOOR WIRE (FOR OPEN)
H102130E01
  1. Disconnect the connectors from the center airbag sensor assembly and the front passenger side - side airbag sensor.

  1. LHD (with curtain shield airbag):Using a service wire, connect J16-4 (BBR+) and J16-3 (BBR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. LHD (without curtain shield airbag):Using a service wire, connect J39-2 (BBR+) and J39-1 (BBR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. RHD (with curtain shield airbag):Using a service wire, connect J17-4 (BBL+) and J17-3 (BBL-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. RHD (without curtain shield airbag):Using a service wire, connect J40-2 (BBL+) and J40-1 (BBL-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J9-8 (BBP+) - J9-11 (BBP-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (FOR SHORT)
H100846E02
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J9-8 (BBP+) - J9-11 (BBP-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (TO B+)
H100846E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J9-8 (BBP+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    J9-11 (BBP-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (TO GROUND)
H100846E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J9-8 (BBP+) - Body ground
    Always
    1 MΩ or Higher
    J9-11 (BBP-) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


7. CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR
H100847E02
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front passenger side - side airbag sensor with the driver side - side airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1625/22 is output. (with curtain shield airbag)
    A
    DTC B1625/22 is output. (without curtain shield airbag)
    B
    DTC B1620/21 is output.
    C
    Neither DTC B1620/21 nor B1625/22 is output.
    D



A
Go to step 8

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C
REPLACE FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR
D

USE SIMULATION METHOD TO CHECK

8. CHECK FLOOR WIRE (FOR OPEN)
H100165E02
  1. Disconnect the connectors from the front passenger side side airbag sensor and the front passenger side rear airbag sensor.

  1. LHD:Using a service wire, connect J14-1 (BCR-) and J14-2 (BCR+) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. RHD:Using a service wire, connect J15-1 (BCL-) and J15-2 (BCL+) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - J16-2 (BCR-) (*1)
    Always
    Below 1 Ω
    J17-1 (BCL+) - J17-2 (BCL-) (*2)
    Always
    Below 1 Ω

*1: LHD
*2: RHD


NG
REPAIR OR REPLACE FLOOR WIRE
OK


9. CHECK FLOOR WIRE (FOR SHORT)
H100153E02
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - J16-2 (BCR-) (*1)
    Always
    1 MΩ or Higher
    J17-1 (BCL+) - J17-2 (BCL-) (*2)
    Always
    1 MΩ or Higher

    *1: LHD*2: RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


10. CHECK FLOOR WIRE (TO B+)
H100153E02
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - Body ground (*1)
    Ignition switch on (IG)
    Below 1 V
    J16-2 (BCR-) - Body ground (*1)
    Ignition switch on (IG)
    Below 1 V
    J17-1 (BCL+) - Body ground (*2)
    Ignition switch on (IG)
    Below 1 V
    J17-2 (BCL-) - Body ground (*2)
    Ignition switch on (IG)
    Below 1 V

    *1:LHD*2:RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


11. CHECK FLOOR WIRE (TO GROUND)
H100153E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J16-1 (BCR+) - Body ground (*1)
    Always
    1 MΩ or Higher
    J16-2 (BCR-) - Body ground (*1)
    Always
    1 MΩ or Higher
    J17-1 (BCL+) - Body ground (*2)
    Always
    1 MΩ or Higher
    J17-2 (BCL-) - Body ground (*2)
    Always
    1 MΩ or Higher

    *1:LHD*2:RHD



NG
REPAIR OR REPLACE FLOOR WIRE
OK


12. CHECK FRONT PASSENGER SIDE REAR AIRBAG SENSOR
H100848E03
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front passenger side rear airbag sensor with the driver side rear airbag sensor and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1625/22 is output.
    A
    DTC B1620/21 is output.
    B
    Neither DTC B1620/21 nor B1625/22 is output.
    C

    HINT:
    DTCs other than B1625/22 and B1620/21 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT PASSENGER SIDE REAR AIRBAG SENSOR
C

USE SIMULATION METHOD TO CHECK


← B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction (from Aug 2005)B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction (from Aug 2005) →