B1630/23 Driver Side Rear Airbag Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2005
DESCRIPTION
The driver side rear airbag sensor consists of parts including the diagnostic circuit and the lateral deceleration sensor.When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1630/23 is recorded when a malfunction is detected in the driver side rear airbag sensor circuit.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| B1630/23 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
![]() ![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1630/23 is not output.
- HINT:
- DTCs other than DTC B1630/23 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the driver side rear airbag sensor.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK FLOOR WIRE (FOR OPEN) |
![]() ![]() |
Disconnect the connectors from the driver side - side airbag sensor and the driver side rear airbag sensor.
LHD:Using a service wire, connect J15-2 (BCL+) and J15-1 (BCL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
RHD:Using a service wire, connect J14-2 (BCR+) and J14-1 (BCR-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
J17-1 (BCL+) - J17-2 (BCL-) (*1)
Always
Below 1 Ω
J16-1 (BCR+) - J16-2 (BCR+) (*2)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK FLOOR WIRE (FOR SHORT) |
![]() ![]() |
Disconnect the service wire from connector C.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
J17-1 (BCL+) - J17-2 (BCL-) (*1)
Always
1 MΩ or higher
J16-1 (BCR+) - J16-2 (BCR-) (*2)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 5. CHECK FLOOR WIRE (TO B+) |
![]() ![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
J17-1 (BCL+) - Body ground (*1)
Ignition switch on (IG)
Below 1 V
J17-2 (BCL-) - Body ground (*1)
Ignition switch on (IG)
Below 1 V
J16-1 (BCR+) - Body ground (*2)
Ignition switch on (IG)
Below 1 V
J16-2 (BCR-) - Body ground (*2)
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 6. CHECK FLOOR WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
J17-1 (BCL+) - Body ground (*1)
Always
1 MΩ or higher
J17-2 (BCL-) - Body ground (*1)
Always
1 MΩ or higher
J16-1 (BCR+) - Body ground (*2)
Always
1 MΩ or higher
J16-2 (BCR-) - Body ground (*2)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 7. CHECK DRIVER SIDE REAR AIRBAG SENSOR |
![]() ![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the driver side rear airbag sensor with the front passenger side rear airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- Result:
Result
Proceed to
DTC B1630/23 is output.
A
DTC B1635/24 is output.
B
DTC B1630/23 and B1635/24 are not output.
C
- HINT:
- DTCs other than DTC B1630/23 and B1635/24 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | ||
| ||
| 8. CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the driver side rear airbag sensor and front passenger side rear airbag sensor to their original positions and connect the connectors to them.
Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1630/23 is output.
A
DTC B1635/24 is output.
B
Neither DTC B1630/23 nor B1635/24 is output.
C
- HINT:
- DTCs other than B1630/23 and B1635/24 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | ||
| ||





