2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL BRAKE ACTUATOR NO. 1 BRACKET

C130321
  1. Install the actuator bracket with the 2 bolts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }

    NOTICE:
    Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.


2. INSTALL BRAKE ACTUATOR BRACKET

C128969
  1. Install the actuator bracket with the 3 bolts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


3. INSTALL BRAKE ACTUATOR

C128966E01
  1. Provisionally install the actuator bracket with the 3 bolts in the sequence shown in the illustration.

  1. Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Connect the brake actuator connector.


4. INSTALL BRAKE TUBE (for LHD)

C116918
  1. Connect a new brake tube clamp.

  1. C128965E01
    Using SST, install each brake tube into the correct position on the actuator, as shown in the illustration.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Do not damage the brake tubes.

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. C128963E01
    Using SST, install the 2 brake tubes onto the brake master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. C116915E01
    Using SST, install the 2 brake tubes onto the brake tube No. 1 way.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. C116914E01
    Using SST, install the brake tube onto the front flexible hose.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


5. INSTALL BRAKE TUBE (for RHD)

C128968E01
  1. Using SST, install each brake tube into the correct position on the actuator, as shown in the illustration.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Do not damage the brake tubes.

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


6. INSTALL BATTERY CARRIER

Torque:
17 N*m{ 175 kgf*cm , 13 ft.*lbf }


7. INSTALL BATTERY TRAY

8. INSTALL BATTERY

9. INSTALL COWL TOP NO. 1 VENTILATOR LOUVER CENTER (for LHD)

  1. A125670
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.

  1. Connect the washer hose.


10. INSTALL COWL TOP NO. 2 VENTILATOR LOUVER CENTER (for RHD)

  1. A125782
    Engage the 2 hooks and install cowl top ventilator louver center No. 2.


11. INSTALL HOOD TO COWL TOP SEAL

  1. E113851
    Engage the 7 clips and install the hood to cowl top seal.


12. FILL RESERVOIR WITH BRAKE FLUID

C137247E01
  1. Remove the cowl top ventilator louver.

  1. C130290E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


13. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C130291E01
    w/o VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-00100  

  1. w/ VSC:

    1. Using SST, disconnect the brake tubes from the master cylinder.

      SST
      09023-38200  

  1. C130292E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C130293E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C130291E01
    w/o VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. w/ VSC:

    1. Using SST, connect the brake tubes to the master cylinder.

      SST
      09023-38200  

      Torque:
      for use without SST:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }
      for use with SST:
      18 N*m{ 180 kgf*cm , 13 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.


14. BLEED BRAKE LINE

C130294
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc Brake:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }
    Rear Drum Brake:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Rear Disc Brake:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


15. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT4


16. CHECK FOR BRAKE FLUID LEAKAGE

17. CHECK ACTUATOR WITH INTELLIGENT TESTER
(Click here)
← REMOVAL (from Nov 2005)COMPONENTS (from Aug 2005) →