2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL PARKING BRAKE CABLE

C130287
  1. for Rear Drum Brake:

    1. Install the parking brake cable onto the backing plate.

  1. C129770
    for Rear Disc Brake:

    1. Install the casing cap onto the rear disc brake cylinder guide.

    2. Connect the cable end to the rear disc brake cylinder operation lever.

  1. Install a new cable clamp B onto the rear axle beam.

    NOTICE:
    Securely install the clamp.

  1. Tighten the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Pass the parking brake cable through a new cable clamp A, and then install cable clamp A onto the stud bolt.

    NOTICE:
    Securely install the clamp.

  1. Connect the cable end to the equalizer.

    C130288E01


2. INSTALL FRONT FLOOR NO. 4 HEAT INSULATOR (for 1KR-FE and 2SZ-FE)

C108997
  1. Install the heat insulator with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


3. APPLY HIGH TEMPERATURE GREASE (for Rear Drum Brake)

C130277E01
  1. Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.


4. INSTALL REAR BRAKE SHOE (for Rear Drum Brake)

C130273
  1. Using needle-nose pliers, connect the parking brake cable onto the parking brake shoe lever.

  1. C130272
    Using pliers, install the rear brake shoe, pin and shoe hold down spring.


5. INSTALL PARKING BRAKE SHOE STRUT SET (for Rear Drum Brake)

C130278E01
  1. Apply high temperature grease to the adjusting bolt.

  1. C130279E01
    Install the parking brake shoe strut set as shown in the illustration.


6. INSTALL FRONT BRAKE SHOE (for Rear Drum Brake)

C130271
  1. Using pliers, install the front brake shoe, pin and shoe hold down spring.

  1. C129776E01
    Using SST, install the tension spring.
    SST
    09703-30010  

  1. C129775E01
    Using SST, install the return shoe spring.
    SST
    09703-30010  

    NOTICE:
    Do not damage the wheel cylinder boot.


7. CHECK REAR DRUM BRAKE INSTALLATION (for Rear Drum Brake)

  1. Check that each part is installed properly.

    C130280E01

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.


8. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

9. ADJUST CLEARANCE BETWEEN BRAKE SHOES AND DRUM (for Rear Drum Brake)
  1. Remove the rear brake drum.

  1. C130281
    Measure the brake drum inner diameter and the diameter of the brake shoes. Check that the difference between the diameters is equal to the specified shoe clearance.

    Shoe clearance:
    0.6 mm (0.024 in.)

  1. Install the rear brake drum.


10. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


11. INSPECT PARKING BRAKE LEVER TRAVEL
  1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    Rear Brake type
    Number of clicks
    Drum
    5 to 8
    Disc
    4 to 7


12. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Drum Brake)
  1. Completely release the parking brake lever.

  1. C129772
    Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    5 to 8 clicks at 200 N (20 kgf 45 lbf)

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


13. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Disc Brake)
  1. Completely release the parking brake lever.

  1. Loosen the adjusting nut to completely release the parking brake cable.

  1. Strongly step on the brake pedal 3 to 5 times with the engine stopped.

  1. C129772
    Turn the new adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    4 to 7 clicks at 200 N (20 kgf 45 lbf)

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. C130289E01
    Release the parking brake lever and check that the clearance measurement between the rear disc brake cylinder operation lever and the stopper is within the specified range.

    Clearance:
    0 to 0.5 mm (0 to 0.02 in.)

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


14. INSTALL REAR CONSOLE BOX ASSEMBLY

C116873
  1. Engage the 2 clips and install the console box with the bolt.


15. INSTALL CONSOLE BOX CARPET

C109008
  1. Install the console box carpet.


16. INSTALL CONSOLE BOX REAR COVER

C109006E01
  1. Engage the 8 claws to install the console box rear cover.


17. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Engage the 6 claws to install the shifting hole cover.


18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
← REMOVAL (from Nov 2005)COMPONENTS (from Jan 2006) →