2005-2008 Yaris · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

2. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Disengage the 6 claws and remove the shifting hole cover.


3. REMOVE CONSOLE BOX REAR COVER

C109006E01
  1. Disengage the 8 claws and remove the console box rear cover.


4. REMOVE CONSOLE BOX CARPET

C109008
  1. Remove the console box carpet.


5. REMOVE REAR CONSOLE BOX ASSEMBLY

C116873
  1. Remove the bolt and disengage the 2 clips to remove the console box.


6. REMOVE REAR WHEEL

7. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)
  1. Release the parking brake and remove the rear brake drum.
    If the rear brake drum cannot be removed easily, perform the following procedure.

  1. for Manual Transaxle:

    1. Remove the shift lever knob.

    2. Remove the shifting hole cover (Click here).

  1. Remove the console box rear cover (Click here).

  1. Remove the console box carpet (Click here).

  1. Remove the rear console box (Click here).

  1. C129772
    Loosen the wire adjusting nut.

    NOTICE:
    Do not reuse the loosened nut.

  1. C129773
    Remove the hole plug.

  1. C129774E01
    Insert SST through the hole in the backing plate, pull the parking brake shoe lever toward the rear of the vehicle and remove the rear brake drum.
    SST
    09921-00010  


8. REMOVE FRONT BRAKE SHOE (for Rear Drum Brake)

C129775E01
  1. Using SST, remove the return shoe spring.

    SST
    09703-30010  

    NOTICE:
    Do not damage the wheel cylinder boot.

  1. C129776E01
    Using SST, remove the tension spring.
    SST
    09703-30010  

  1. C130271
    Using pliers, remove the shoe hold down spring, pin and front brake shoe.


9. REMOVE PARKING BRAKE SHOE STRUT SET (for Rear Drum Brake)

NOTICE:
Do not disassemble the strut set, and be careful not to damage or bend any of the components.


10. REMOVE REAR BRAKE SHOE (for Rear Drum Brake)

C130272
  1. Using pliers, remove the shoe hold down spring, pin and rear brake shoe.

  1. C130273
    Using needle-nose pliers, disconnect the parking brake cable from the parking brake shoe lever.


11. REMOVE FRONT FLOOR NO. 4 HEAT INSULATOR (for 1KR-FE and 2SZ-FE)

C108997
  1. Remove the 2 nuts and remove the heat insulator.


12. REMOVE PARKING BRAKE CABLE

C130285
  1. Remove the adjusting nut.

  1. Disconnect the cable end from the equalizer.

  1. Remove cable clamp A from the body.

  1. Remove the 4 bolts.

  1. Using pliers, pinch both ends of the claw of cable clamp B and flex the clamp to remove it.

    C130286E01

  1. for Rear Disc Brake (RH Side):

    1. Remove the cable clamp B from the axle beam.

      HINT:
      Break the cable clamp to remove it.

  1. C130287
    for Rear Drum Brake:

    1. Squeeze the point indicated by the arrow and pull out the parking brake cable.

  1. C129757
    for Rear Disc Brake:

    1. Disconnect the cable end from the rear disc brake cylinder operation lever.

    2. Using needle-nose pliers, disengage the claw of the casing cap and disconnect the parking brake cable.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →