2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL PARKING BRAKE CABLE

C109000
  1. Install the parking brake cable onto the backing plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install a new cable clamp B onto the rear axle beam.

    NOTICE:
    Securely install the clamp.

  1. Tighten the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Pass the parking brake cable through a new cable clamp A, and then install cable clamp A onto the stud bolt.

    NOTICE:
    Securely install the clamp.

  1. Connect the cable end to the equalizer.

    C133133E01


2. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR

C108997
  1. Install the heat insulator with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


3. INSTALL REAR BRAKE SHOE KIT

C116953E01
  1. Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.

  1. C108972
    Using needle-nose pliers, install the parking brake cable onto the parking brake shoe lever.

  1. C108971E01
    Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.
    SST
    09718-00010  

  1. F050549E01
    Apply high temperature grease to the adjusting bolt.

  1. F040013E01
    Install the parking brake shoe strut set as shown in the illustration.

  1. C108969E01
    Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.
    SST
    09718-00010  

  1. F042698
    Using needle-nose pliers, install the tension spring onto the front brake shoe and rear brake shoe.

  1. C108968E01
    Using SST, install the shoe return spring onto the front brake shoe.
    SST
    09703-30010  

    NOTICE:
    Do not damage the wheel cylinder boot.


4. CHECK REAR DRUM BRAKE INSTALLATION

  1. Check that each part is installed properly.

    C108977E01

  1. C116892
    Measure the brake drum inner diameter and the diameter of the brake shoes. Check that the difference between the diameters is equal to the specified shoe clearance.

    Shoe clearance:
    0.6 mm (0.024 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.


5. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

6. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

F040023E03
  1. Provisionally install the 2 hub nuts.

  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

  1. Using a screwdriver, release the adjuster 12 notches.

  1. Install the hole plug.


7. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


8. INSPECT PARKING BRAKE LEVER TRAVEL
  1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

    Parking brake lever travel:
    6 to 9 clicks at 200 N (20 kgf, 45 lbf)


9. ADJUST PARKING BRAKE LEVER TRAVEL

C116905E01
  1. Loosen the lock nut and turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    6 to 9 clicks at 200 N (20 kgf, 45 lbf)

  1. Tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


10. INSTALL REAR CONSOLE BOX ASSEMBLY

  1. B132349
    Engage the 4 claws and install the rear console box.

  1. Install the 2 bolts and 2 screws.

  1. Connect the clamp.


11. INSTALL CONSOLE BOX CARPET

  1. B132346
    Install the console box carpet.


12. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY

  1. B132348
    Connect the connector.

  1. Engage the 3 clips and 3 claws and install the console upper rear panel.


13. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B132347
    Engage the 5 clips and the claw and install the upper console panel.


14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B132388
    Install the shift lever knob.


15. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.

← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →