2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL PARKING BRAKE LEVER

C129753
  1. Install the parking brake lever with the 2 bolts.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }


2. INSTALL PARKING BRAKE EQUALIZER

C129752
  1. Install the parking brake equalizer.

  1. Connect the parking brake cable to the parking brake equalizer.

  1. Temporarily tighten the wire adjusting nut.


3. INSTALL PARKING BRAKE SWITCH

C129755
  1. Install the parking brake switch with the screw.

  1. Connect the parking brake switch connector.


4. INSPECT PARKING BRAKE LEVER TRAVEL
  1. Slowly pull the parking brake lever to the fully applied position, counting the number of clicks.

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    Rear Brake type
    Number of clicks
    Drum
    5 to 8
    Disc
    4 to 7


5. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Drum Brake)
  1. Completely release the parking brake lever.

  1. C129772
    Turn the adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    5 to 8 clicks at 200 N (20 kgf 45 lbf)

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


6. ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Disc Brake)
  1. Completely release the parking brake lever.

  1. Loosen the adjusting nut to completely release the parking brake cable.

  1. Strongly step on the brake pedal 3 to 5 times with the engine stopped.

  1. C129772
    Turn the new adjusting nut until the parking brake lever travel is corrected to within the specified range.

    Parking brake lever travel:
    4 to 7 clicks at 200 N (20 kgf 45 lbf)

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check whether the parking brake drags or not.

  1. C130289E01
    Release the parking brake lever and check that the clearance measurement between the rear disc brake cylinder operation lever and the stopper is within the specified range.

    Clearance:
    0 to 0.5 mm (0 to 0.02 in.)

  1. When operating the parking brake lever, check that the brake warning light illuminates.

    Standard:
    Brake warning light always illuminates at the first click.


7. INSTALL REAR CONSOLE BOX ASSEMBLY

C116873
  1. Engage the 2 clips and install the console box with the bolt.


8. INSTALL CONSOLE BOX CARPET

C109008
  1. Install the console box carpet.


9. INSTALL CONSOLE BOX REAR COVER

C109006E01
  1. Engage the 8 claws to install the console box rear cover.


10. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)

C109005E01
  1. Engage the 6 claws to install the shifting hole cover.


11. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Nov 2005)COMPONENTS (from Jan 2006) →