Removal / installation · Vehicles built Aug 2005 – Oct 2005
Versions by build date: Aug 2005 – Oct 2005from Nov 2005
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.
REMOVE CENTER STOP LIGHT COVER
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 rear light covers.
Remove the 2 screws.
Disengage the 2 claws.
Disconnect the connector and remove the center stop light cover.
3.
REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY
Disengage the 2 claws and remove the high mounted stop light.
4.
REMOVE BACK DOOR TRIM BOARD ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, slide the handle plate of the back door trim board to disengage it.
Disengage the 3 claws and 9 clips and remove the back door trim board.
5.
REMOVE REAR WIPER ARM AND BLADE ASSEMBLY
Open the rear wiper arm head cap.
Remove the nut and rear wiper arm and blade.
6.
REMOVE REAR WIPER MOTOR GROMMET
Remove the rear wiper motor grommet.
7.
REMOVE REAR WIPER MOTOR
Disconnect the connector.
Loosen bolt A.
NOTICE:
Do not try to remove the bolt since it is integrated with the motor.
Remove bolt B and the rear wiper motor.
8.
REMOVE BACK DOOR PANEL NO.2 PROTECTOR
Disengage the claw and clip, then remove back door panel protector No. 2.
NOTICE:
Remove any tape remaining on the back door side.
9.
REMOVE BACK DOOR PANEL NO.1 PROTECTOR
HINT:
Use the same procedure as described for the No. 2 protector.
10.
REMOVE BACK DOOR LOCK ASSEMBLY
Disconnect the connector and the clamp.
Remove the 3 bolts and the back door lock.
11.
REMOVE BACK DOOR OUTSIDE HANDLE (w/ Entry and Start System)
Disconnect the connector.
Disengage the claw and the clamp.
Remove the bolt and the back door outside handle.
12.
REMOVE BACK DOOR LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)
Remove the bolt and back door lock cylinder assembly.
13.
REMOVE BACK DOOR OUTSIDE HANDLE (w/o Entry and Start System)
Remove the back door outside handle from the back door panel.
14.
REMOVE BACK DOOR LOCK ACTUATOR ASSEMBLY (w/o Entry and Start System)
Disconnect the connector.
Remove the 2 bolts and the back door lock actuator.
15.
REMOVE SYMBOL EMBLEM
Apply protective tape to the back door panel in the area around the symbol emblem.
Using an infrared light, heat the symbol emblem.
CAUTION:
Do not burn yourself with the heated back door panel or infrared light.
HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the symbol emblem.
Remove the protective tape.
16.
REMOVE NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE
Apply protective tape to the back door panel in the area around the No. 1 luggage compartment door name plate.
Using an infrared light, heat the No. 1 luggage compartment door name plate.
CAUTION:
Do not burn yourself with the heated back door panel or infrared light.
HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 1 luggage compartment door name plate.
Remove the protective tape.
17.
REMOVE NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE
Apply protective tape to the back door panel in the area around the No. 2 luggage compartment door name plate.
Using an infrared light, heat the No. 2 luggage compartment door name plate.
CAUTION:
Do not burn yourself with the heated back door panel or infrared light.
HINT:
Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 2 luggage compartment door name plate.