2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL BRAKE PEDAL PAD
  1. Install the brake pedal pad onto the brake pedal.


2. INSTALL BRAKE PEDAL BUSH
  1. Apply lithium soap base glycol grease to the 2 bushes.

  1. Install the 2 bushes onto the brake pedal.


3. INSTALL BRAKE PEDAL
  1. Install the brake pedal onto the pedal support with the brake pedal shaft and nut.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


4. INSTALL BRAKE PEDAL SUPPORT

C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. C116880
    Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.


6. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

C116879
  1. Install a new stop light switch mounting adjuster onto the pedal support.


7. INSTALL STOP LIGHT SWITCH

F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.

  1. F049044E08
    Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the wire harness clamp onto the pedal support.

  1. Connect the connector to the stop light switch.


8. INSPECT AND ADJUST BRAKE PEDAL
  1. Remove the instrument panel under tray (Click here).

  1. C116874E01
    Inspect the brake pedal height.

    Pedal height from floor:
    107.3 to 117.3 mm (4.224 to 4.618 in.)

    If the pedal height is incorrect, adjust it.

  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor:
      107.3 to 117.3 mm (4.224 to 4.618 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. F049043E01
      Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.

    7. F049044E08
      Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    8. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    9. Connect the connector to the stop light switch.

  1. F048932E01
    Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.

  1. R000934E02
    Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):

      LHD
      RHD
      w/ ABS
      More than 73 mm (2.87 in.)
      More than 71 mm (2.80 in.)
      w/o ABS
      More than 70 mm (2.75 in.)
      -

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.

  1. Install the instrument panel under tray (Click here).


9. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. G028410E01
    Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on No. 2 steering intermediate shaft assembly and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


10. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


11. INSTALL INSTRUMENT PANEL UNDER TRAY

B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B132390
    Engage the 4 claws and install the instrument panel under tray.


12. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.

  1. Engage the 7 clips at the rear side of the instrument panel.

    B132324

  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. B132386
    Connect the passenger airbag connector and clamp.


13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B132319E01
    Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.


14. INSTALL FRONT PILLAR GARNISH RH

  1. B138439E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134787
    Install the 3 clamps.

  1. Connect the antenna connector.

  1. B134781E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134779
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


15. INSTALL FRONT PILLAR GARNISH LH

  1. B138440
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134789
    Install the 4 clamps.

  1. B134782E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134780
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


18. INSTALL COMBINATION METER ASSEMBLY

E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.


19. INSTALL INSTRUMENT CLUSTER FINISH PANEL

E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. E116834
    Engage the 5 claws and 5 clips and install the instrument cluster finish panel.


20. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.


21. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.


22. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


24. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →