INSTALLATION
Removal / installation · Vehicles built Aug 2005 – Dec 2005
Versions by build date: Aug 2005 – Dec 2005 from Jan 2006
| 1.
INSTALL ECM BRACKET NO. 2 |
 |
Install ECM bracket No. 2 with the 2 screws.
| 2.
INSTALL ECM BRACKET |
 |
Install the ECM bracket with the 2 screws.
| 3.
INSTALL ECM |
 |
Install the ECM with the bolt and 2 nuts.
-
Torque:
- 8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
Connect the 2 ECM connectors.
- Install the 2 lock knobs and harness clamp.
| 4.
INSTALL COWL TOP PANEL OUTER
|
 |
Install the cowl top panel with the 9 bolts.
-
Torque:
- 6.5 N*m{
66 kgf*cm
, 57 in.*lbf
}
- Connect the wire harness clamp.
| 5.
INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2
|
 |
Engage the claw to install cowl to register duct No. 2.
| 6.
INSTALL WINDSHIELD WIPER MOTOR AND LINK
|
 |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
| 7.
INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)
|
 |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 8.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)
|
 |
Connect the washer hose.
- Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
- Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 9.
INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)
|
 |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 10.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSY (for RHD)
|
 |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 11.
INSTALL HOOD TO COWL TOP SEAL
|
 |
Engage the 7 clips and install the hood to cowl top seal.
| 12.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
|
 |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 13.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
|
 |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 14.
INSTALL FRONT WIPER ARM HEAD CAP
|
 |
Engage the claw and install the 2 front wiper arm head caps.
| 15.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}