INSTALLATION
Removal / installation · Vehicles built from Jan 2006
Versions by build date: Aug 2005 – Dec 2005 from Jan 2006
| 1.
INSTALL ECM BRACKET NO. 2 |
 |
Install ECM bracket No. 2 with the 2 screws.
| 2.
INSTALL ECM BRACKET |
 |
Install the ECM bracket with the 2 screws.
| 3.
INSTALL ECM |
 |
Install the ECM with the bolt and 2 nuts.
-
Torque:
- 8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
Connect the 2 ECM connectors.
- Install the 2 lock knobs and harness clamp.
| 4.
INSTALL COWL TOP PANEL OUTER (for Hatchback)
|
 |
Install the cowl top panel with the 9 bolts.
-
Torque:
- 6.5 N*m{
66 kgf*cm
, 57 in.*lbf
}
- Connect the wire harness clamp.
| 5.
INSTALL COWL TOP PANEL OUTER (for Sedan) |
 |
Install the cowl top panel outer and install the 8 bolts.
-
Torque:
- 6.5 N*m{
66 kgf*cm
, 58 in.*lbf
}
- Install the cowl top panel outer center bracket and install the 2 bolts.
-
Torque:
- 6.5 N*m{
66 kgf*cm
, 58 in.*lbf
}
- Connect the wire harness and engage the claw.
| 6.
INSTALL FRONT AIR SHUTTER SEAL RH (for Sedan) |
 |
Install the front air shutter seal and engage the 3 claws.
| 7.
INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback)
|
 |
Engage the claw to install cowl to register duct No. 2.
| 8.
INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Hatchback)
|
 |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
| 9.
INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Sedan)
|
 |
- Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
| 10.
INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback LHD)
|
 |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 11.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback LHD)
|
 |
Connect the washer hose.
- Engage the 11 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
- Engage the 2 hooks and install cowl top ventilator louver center No. 1.
| 12.
INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback RHD)
|
 |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 13.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback RHD)
|
 |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 14.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)
|
 |
- Connect the washer hoses.
Engage the 5 hooks.
- Engage the 10 hooks and the 6 claws.
Install the cowl top ventilator louver sub-assembly with the 2 clips.
| 15.
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)
|
 |
- Connect the washer hoses.
Engage the 5 hooks.
- Engage the 8 hooks and the 4 claws.
Install the cowl top ventilator louver sub-assembly with the 3 clips.
| 16.
INSTALL HOOD TO COWL TOP SEAL (for Hatchback)
|
 |
Engage the 7 clips and install the hood to cowl top seal.
| 17.
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)
|
 |
- Engage the 3 claws and install the cowl side ventilator sub-assembly LH.
| 18.
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 19.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Hatchback)
|
 |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 20.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for Sedan)
|
 |
- Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 21.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Hatchback)
|
 |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 22.
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for Sedan)
|
 |
- Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
- Align the blade tip with the mark on the windshield glass, as shown in the illustration.
Tighten the nut of the front wiper arm.
-
Torque:
- 26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
| 23.
INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback)
|
 |
Engage the claw and install the 2 front wiper arm head caps.
| 24.
INSTALL FRONT WIPER ARM HEAD CAP (for Sedan)
|
 |
- Engage the claw and install the 2 front wiper arm head caps.
| 25.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}