INSTALLATION
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL ECM BRACKET NO. 2 |
![]() ![]() |
Install ECM bracket No. 2 with the 2 screws.
| 2. INSTALL ECM BRACKET |
![]() ![]() |
Install the ECM bracket with the 2 screws.
| 3. INSTALL ECM |
![]() ![]() |
Install the ECM with the bolt and 2 nuts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 2 ECM connectors.
Install the 2 lock knobs and harness clamp.

| 4. INSTALL COWL TOP PANEL OUTER (for RHD) |
![]() ![]() |
Install the cowl top panel with the 9 bolts.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 57 in.*lbf }
Connect the wire harness clamp.

| 5. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for RHD) |
![]() ![]() |
Engage the claw to install cowl to register duct No. 2.
| 6. INSTALL WINDSHIELD WIPER MOTOR AND LINK (for RHD) |
![]() ![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 7. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 9. INSTALL HOOD TO COWL TOP SEAL (for RHD) |
![]() ![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH (for RHD) |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 11. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH (for RHD) |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 12. INSTALL FRONT WIPER ARM HEAD CAP (for RHD) |
Engage the claw and install the 2 front wiper arm head caps.

| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }









