2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. INSTALL ECM BRACKET NO. 2

A106940
  1. Install ECM bracket No. 2 with the 2 screws.


2. INSTALL ECM BRACKET

A106941
  1. Install the ECM bracket with the 2 screws.


3. INSTALL ECM

A105635
  1. Install the ECM with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 ECM connectors.

  1. A107404
    Install the 2 lock knobs and harness clamp.


4. INSTALL COWL TOP PANEL OUTER (for Hatchback)

A107444
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }

  1. A117320
    Connect the wire harness clamp.


5. INSTALL COWL TOP PANEL OUTER (for Sedan)

A133328
  1. Install the cowl top panel outer and install the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A133326
    Install the cowl top panel outer center bracket and install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A133322
    Connect the wire harness and engage the claw.


6. INSTALL FRONT AIR SHUTTER SEAL (for Sedan)

A133324
  1. Install the front air shutter seal and engage the 3 claws.


7. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 (for Hatchback)

A108951
  1. Engage the claw to install cowl to register duct No. 2.


8. INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Hatchback)

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


9. INSTALL WINDSHIELD WIPER MOTOR AND LINK (for Sedan)

  1. E127840
    Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


10. INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


11. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Hatchback)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


12. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan RHD)

  1. E127836
    Connect the washer hoses.

  1. Engage the 5 hooks.

  1. E127835
    Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.


13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for Sedan LHD)

  1. E127839
    Connect the washer hoses.

  1. Engage the 5 hooks.

  1. E127838
    Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.


14. INSTALL HOOD TO COWL TOP SEAL (for Hatchback)

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


15. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan)

  1. E129651
    Engage the 3 claws and install the cowl side ventilator sub-assembly LH.


16. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan)

HINT:
Use the same procedure as for the LH side.


17. INSTALL FRONT WIPER ARM AND BLADE LH (for Hatchback)

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


18. INSTALL FRONT WIPER ARM AND BLADE LH (for Sedan)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


19. INSTALL FRONT WIPER ARM AND BLADE RH (for Hatchback)

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


20. INSTALL FRONT WIPER ARM AND BLADE RH (for Sedan)

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E129694E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


21. INSTALL FRONT WIPER ARM HEAD CAP (for Hatchback)

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


22. INSTALL FRONT WIPER ARM HEAD CAP (for Sedan)

  1. E127841
    Engage the claw and install the 2 front wiper arm head caps.


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← INSTALLATION (Aug 2005 – Dec 2005)COMPONENTS (from Aug 2005) →