2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2005 – Dec 2005

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. INSTALL ECM BRACKET NO. 2

A106940
  1. Install ECM bracket No. 2 with the 2 screws.


2. INSTALL ECM BRACKET

A106941
  1. Install the ECM bracket with the 2 screws.


3. INSTALL ECM

A105635
  1. Install the ECM with the bolt and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 ECM connectors.

  1. A107404
    Install the 2 lock knobs and harness clamp.


4. INSTALL COWL TOP PANEL OUTER

A107444
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }

  1. A117320
    Connect the wire harness clamp.


5. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A108951
  1. Engage the claw to install cowl to register duct No. 2.


6. INSTALL WINDSHIELD WIPER MOTOR AND LINK

E107891
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


7. INSTALL COWL TOP VENTILATOR LOUVER LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117366E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117367E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


9. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


10. INSTALL FRONT WIPER ARM AND BLADE LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117366E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


11. INSTALL FRONT WIPER ARM AND BLADE RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. A117367E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


12. INSTALL FRONT WIPER ARM HEAD CAP

  1. E107898
    Engage the claw and install the 2 front wiper arm head caps.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Jan 2006)INSTALLATION (from Jan 2006) →