2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL WATER PUMP ASSEMBLY

A118795
  1. Install the gasket onto the chain cover.

  1. A118794E01
    Provisionally tighten the water pump with the 5 bolts.

  1. Tighten the water pump with the 5 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts and nuts in the sequence shown in the illustration.


2. INSTALL FAN BELT ADJUSTING BAR
  1. Install the fan belt adjusting bar with the bolt.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


3. INSTALL GENERATOR ASSEMBLY

A107405
  1. Provisionally tighten the generator with the 2 bolts.

  1. A104326
    Install the wire harness onto terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 in.*lbf }

  1. Install the terminal cap.

  1. Connect the connector.

  1. Engage the 2 clamps and install the wire harness.


4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


5. INSTALL FAN AND GENERATOR V BELT

A117085E01
  1. Install the fan and generator V belt.

  1. Gently tighten bolt B until there is no measurable clearance.

  1. Turn bolt C to adjust the tension of the fan and generator V belt.

  1. Inspect the fan and generator V belt.

  1. Tighten bolt B.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Visually check the generator wiring and listen for abnormal noise.

    1. Check that the wiring is in good condition.

    2. Check that there is no abnormal noise from the generator while the engine is running.

  1. B000540E04
    Inspect the discharge warning light circuit.

    1. Turn the ignition switch to the ON position. Check that the discharge warning light illuminates.

    2. Start the engine. Check that the light goes off.


6. INSPECT DRIVE BELT DEFLECTION AND TENSION

A106802E01
  1. Check the belt deflection by pressing on the belt at the points indicated by the arrow marks in the illustration.

    Deflection:
    Item
    Specified Condition
    New belt
    7 to 8 mm (0.28 to 0.31 in.)
    Used belt
    9 to 11 mm (0.35 to 0.43 in.)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. The most appropriate force for the adjustment above is 98 N (10 kgf, 22 lbf).
    2. New belt refers to a belt which has been used on a running engine for less than 5 minutes.
    3. Used belt refers to a belt which has been used on a running engine for 5 minutes or more.
    4. After installing a belt, check that it fits properly in the ribbed grooves.
    5. Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.
    6. After installing a new belt, run the engine for about 5 minutes and recheck the belt tension.

  1. A117085E01
    Adjust fan and generator V belt tension.

    1. Loosen bolt A.

    2. Loosen bolt B.

    3. Gently tighten bolt B until there is no measurable clearance.

    4. Turn bolt C to adjust the tension of the fan and generator V belt.

    5. Tighten bolt B.

      Torque:
      34 N*m{ 347 kgf*cm , 25 ft.*lbf }

    6. Tighten bolt A.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Visually check the generator wiring and listen for abnormal noises.

    1. Check that the wiring is in good condition.

    2. Check that there is no abnormal noise from the generator while the engine is running.

  1. B000540E04
    Inspect the discharge warning light circuit.

    1. Turn the ignition switch to the ON position. Check that the discharge warning light illuminates.

    2. Start the engine. Check that the light goes off.


7. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Disconnect the vinyl hose.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    4.5 liters (4.8 USqts, 4.2 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


8. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A107403
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.

← REMOVAL (from Aug 2005)COMPONENTS (from Aug 2005) →