2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A116530E01
  1. Remove the 4 clamps.

  1. Remove the 2 clamps and remove the air cleaner cap.


3. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

A104300
  1. Remove the air cleaner filter element from the cylinder head cover.


4. REMOVE IGNITION COIL NO. 1

A116531
  1. Disconnect the 3 ignition coil connectors.

  1. Remove the 3 bolts and remove the 3 ignition coils.


5. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A105015
  1. Disconnect the VSV connector and disengage the wire harness clamp.

  1. Disconnect vapor feed hoses No. 1 and No. 2.

  1. A107415
    Disconnect the ventilation hose.

  1. A116535
    Remove the bolt and separate the oxygen sensor wire harness.

  1. Separate the wire harness.

  1. A104153E03
    Remove the 13 bolts and 2 nuts in the order shown in the illustration and remove the cylinder head cover with the gasket.


6. REMOVE TIMING GEAR COVER TIGHT PLUG

A107398E01
  1. Using an 8mm socket hexagon wrench, remove the timing gear cover tight plug.


7. REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

A107397E01
  1. Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of timing chain cover (Set the No. 1 piston to the TDC/compression).

  1. Make sure that the timing mark of the camshaft sprocket is at the top.

    HINT:
    If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark comes to the top (Set the No. 1 piston to the TDC/compression).

  1. A104194E02
    Put matchmarks on each plate of the timing chain where the plates are aligned with the matchmarks on the sprockets and camshaft timing sprocket (VVT controller). (*1)

    HINT:
    Omit step *1if the orange mark plates are aligned with the cam sprockets, and the yellow mark plate is aligned with the crankshaft.

  1. Turn the crankshaft pulley slightly counterclockwise.

    NOTICE:
    Do not allow the lifted valve and piston to come into contact with each other when removing the camshaft.

  1. A107400
    Loosen the bolts on the sprocket while holding the hexagonal portion of the camshaft.

  1. A105065E02
    Insert a screwdriver from the plug hole and turn the stopper plate of the timing chain tensioner clockwise to release the lock, and keep it as it is.

    HINT:
    1. The plunger of the timing chain tensioner is locked.
    2. If the stopper plate is locked firmly, slightly turn the hexagonal portion of the camshaft to the right and left.

  1. A105066
    Slightly turn the hexagonal portion of the camshaft clockwise so that the plunger of the timing chain tensioner is pushed by the timing chain.

  1. A104308
    Remove the screwdriver from the plug. Insert the hexagon wrench into the stopper plate hole.

    NOTICE:
    Hold the hexagonal portion of the camshaft.

    HINT:
    Perform this procedure in order to maintain the pressure on the plunger from the timing chain tensioner.

  1. A107401
    Remove the bolt of the sprocket while holding the hexagonal portion of camshaft No. 2.

  1. A105068
    Remove the camshaft timing gear.


8. REMOVE NO. 2 CAMSHAFT

A105069E01
  1. Remove the 15 bolts in the order shown in the illustration.

  1. A107402
    Slide the camshaft timing sprocket toward the engine front until camshaft bearing cap No. 1 comes off.

  1. Remove camshaft bearing caps No. 1 and No. 2.

  1. Remove camshaft No. 2.


9. REMOVE CAMSHAFT

A105071
  1. Remove camshaft assembly No. 1 .

    HINT:
    1. Remove camshaft assembly No. 1 along with the camshaft timing sprocket.
    2. Assemble the camshaft timing sprocket to camshaft assembly No. 1 before installing them.

  1. A105072
    Using a piece of string or the equivalent, fix the timing chain to prevent it from dropping.

← COMPONENTS (from Aug 2005)INSPECTION (from Aug 2005) →