2005-2008 Yaris · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E13
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A115681E02

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned on (IG).

    OK:
    MIL lights up



OK
SYSTEM OK
NG


2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and tester on.

  1. Check the communication between the tester and ECM.

    Result:
    Result
    Proceed To
    Communication is possible
    A
    Communication is not possible
    (Un-leaded gasoline model)
    B
    Communication is not possible
    (Leaded gasoline model)
    C



A
GO TO MIL CIRCUIT

C
Go to step 6
B


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the C17 throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY
B


4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A20 accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL POSITION SENSOR
B


5. CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT)
A107934E11
  1. Disconnect the C17 throttle body connector.

  1. Disconnect the A20 accelerator pedal position sensor connector.

  1. Disconnect the A21 and C20 ECM connectors.

  1. Check the resistance.

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCTA (C20-67) - Body ground
    10 kΩ or higher
    VCPA (A21-57) - Body ground
    VCP2 (A21-58) - Body ground

  1. Reconnect the throttle body connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

6. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the C17 throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY
B


7. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A20 accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL POSITION SENSOR
B


8. CHECK MIL (VARIABLE RESISTOR)
  1. Disconnect the C37 variable resistor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the variable resistor connector.



A
REPLACE VARIABLE RESISTOR
B


9. CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT)

  1. A107934E28
    Disconnect the C17 throttle body connector.

  1. Disconnect the A20 accelerator pedal position sensor connector.

  1. Disconnect the A21 and C20 ECM connectors.

  1. Disconnect the C37 variable resistor connector.

  1. Check the resistance.

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCTA (C20-67) - Body ground
    10 kΩ or higher
    VCPA (A21-57) - Body ground
    VCP2 (A21-58) - Body ground
    VC (C20-117) - Body ground

  1. Reconnect the throttle body connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the variable resistor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← ECM Power Source Circuit (from Aug 2005)Fuel Pump Control Circuit (from Aug 2005) →