Fuel Pump Control Circuit
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the engine is cranked, the ST (Starter) relay drive signal output from the STAR terminal of the ECM is input into the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. Thus, the ECM interprets that the engine is cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.While the NE signal is input into the ECM, when engine is running, the ECM turns the Tr1 on continuously.


WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Check whether the fuel pump operating sound occurs when perform the Active Test on the tester.
- OK:
- Fuel pump operating sound occurs.
|
|
||||
| NG | |
| 2. INSPECT MAIN BODY ECU (C/OPN RELAY INPUT VOLTAGE) |
Measure the voltage between the terminal of the main body ECU and the body ground when the ignition switch is turned on (IG) and off.

- Standard voltage:
Tester Connections
Ignition Switch Conditions
Specified Conditions
4B-11 - Body ground
OFF
Below 1 V
4F-4 - Body ground
4B-11 - Body ground
ON
9 to 14 V
4F-4 - Body ground
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY) |
![]() ![]() |
Remove the integration relay from the engine room Relay Block (R/B).
Disconnect the main body ECU connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
1B-4 - 4F-4
Below 1 Ω
1A-4 - 4B-11
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
4F-4 - Body ground
10 kΩ or higher
4B-11 - Body ground
Reinstall the integration relay.
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT MAIN BODY ECU (C/OPN RELAY) |
Remove the main body ECU.

Check the C/OPN relay resistance.
- Standard resistance:
Tester Connections
Specified Conditions
4B-11 - 4A-8
10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals 4D-1 and 4E-5)
- HINT:
- Relay coil circuit between 4D-1 and 4E-5 is not through IGN fuse.
Reinstall the main body ECU.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM) |
Disconnect the A21 ECM connector.

Disconnect the 4E main body ECU connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Main body ECU (4E-5) - FC (A21-7)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
Main body ECU (4E-5) or FC (A21-7) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND) |
Check the harness and the connectors between the main body ECU and the fuel pump.

Disconnect the 4A main body ECU connector.
Disconnect the J5 fuel pump connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Main body ECU (4A-8) - Fuel pump (J5-4)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
Main body ECU (4A-8) or Fuel pump (J5-4) - Body ground
10 kΩ or higher
Check the harness and the connectors between the fuel pump and the body ground.
Disconnect the J5 fuel pump connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
Fuel pump (J5-5) - Body ground
Below 1 Ω
Reconnect the main body ECU connector.
Reconnect the fuel pump connector.
|
|
||||
| OK | |
| 7. INSPECT FUEL PUMP |
Inspect fuel pump resistance.

Measure the resistance between the terminals.
- Standard resistance:
- 0.2 to 3.0 Ω at 20°C (68°F)
Inspect fuel pump operation.
Apply the battery voltage to both the terminals. Check that the pump operates.
- NOTICE:
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
- Keep the fuel pump as far away from the battery as possible.
- Always switch at the battery side.
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
|
|
||||
| OK | ||
| ||
| 8. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG) and START.
- OK:
Conditions
Starter Signal
Ignition switch on (IG)
OFF
Engine start
ON
|
|
||||
| OK | |
| 9. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the tester while cranking.
- Standard:
- Values are displayed continuously.
|
|
||||
| OK | ||
| ||

