2005-2008 Yaris · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Aug 2005


DATA LIST

HINT:
By reading the Data List displayed on an intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect an intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG) and turn the tester ON.

  5. Select the following menu items: Powertrain / Engine and ECT / Data List.

  6. Check the values by referring to the table below.

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    Injector
    [Injector]
    Injection period of No. 1 cylinder:
    Min.: 0 ms, Max.: 32.64 ms
    1.3 to 3.1 ms: Idling
    -
    IGN Advance
    [Ign Advance]
    Ignition timing advance for No. 1 cylinder:
    Min.: -64°, Max.: 63.5°
    BTDC 0 to 15°: Idling
    -
    Calculate Load
    [Calc Load]
    Calculated engine load by ECM:
    Min.: 0 %, Max.: 100 %
    11 to 25 %: Idling
    15 to 35 %: Running without load (2,500 rpm)
    -
    Vehicle Load
    [Vehicle Load]
    Vehicle load:
    Min.: 0 %, Max.: 25700 %
    -
    Value calculated from MAP and Engine speed
    MAP
    [MAP]
    Intake manifold pressure:
    Min.: 0 kPa, Max.: 255 kPa
    50 to 115 kPa: ignition switch on (IG)
    17 to 39 kPa: Idling
    22 to 50 kPa: 2,500 rpm
    -
    Engine Speed
    [Engine Spd]
    Engine speed:
    Min.: 0 rpm, Max.: 16383.75 rpm
    730 to 830rpm: Idling
    -
    Vehicle Speed
    [Vehicle Spd]
    Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Coolant Temp
    [Coolant Temp]
    Engine coolant temperature:
    Min.: -40°C, Max.: 140°C
    75° to 95°C (167° to 203°F): After warming up engine
    If value is -40°C (-40°F) or less: sensor circuit is open
    If value is 140°C (284°F) or more: sensor circuit is shorted
    Intake Air
    [Intake Air]
    Intake air temperature:
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If value is -40°C (-40°F) or less: sensor circuit is open
    If value is 140°C (284°F) or more: sensor circuit is shorted
    Air-Fuel Ratio
    [Air-Fuel Ratio]
    Air-fuel ratio:
    Min.: 0 , Max.: 1.999
    0.8 to 1.2 : During idling
    -
    EVAP (Purge) VSV
    [Evap Purge VSV]
    EVAP (Purge) VSV control duty:
    Min.: 0 %, Max.: 100 %
    0 to 10 %: During Idling
    Order signal from ECM
    Knock Correct Learn Value
    [Knock Crrt Val]
    Correction learning value of knocking:
    Min.: -64°CA, Max.: 1984°CA
    -14 to 0°CA
    Service data
    Knock Feedback Value
    [Knock FB Val]
    Feedback value of knocking:
    Min.: -64°CA, Max.: 1984°CA
    -4.5 to 0°CA
    Service data
    Accelerator Position No. 1
    [Accel Pos #1]
    Absolute Accelerator Pedal Position (APP) No. 1:
    Min.: 0 %, Max.: 100 %
    10 to 25 %: accelerator pedal released
    60 to 90 %: accelerator pedal depressed
    ETCS service data
    Accelerator Position No. 2
    [Accel Pos #2]
    Absolute APP No. 2:
    Min.: 0 %, Max.: 100 %
    20 to 45 %: accelerator pedal released
    80 to 100 %: accelerator pedal depressed
    ETCS service data
    Accelerator Position No. 1
    [Accel Pos #1]
    APP sensor No. 1 voltage:
    Min.: 0 V, Max.: 5 V
    0.7 to 1.2 V: accelerator pedal released
    2.8 to 4.6 V: accelerator pedal depressed
    ETCS service data
    Accelerator Position No. 2
    [Accel Pos #2]
    APP sensor No. 2 voltage:
    Min.: 0 V, Max.: 5 V
    1.2 to 2.0 V: accelerator pedal released
    3.6 to 4.6 V: accelerator pedal depressed
    ETCS service data
    Accelerator Idle Position
    [Accel Idl Pos]
    Whether or not accelerator pedal position sensor detecting idle:
    OFF or ON
    ON: Idling
    ETCS service data
    Throttle Fully Close Learn
    [Thrtl Learn Val]
    Throttle valve fully closed (learned value):
    Min.: 0 V, Max.: 5 V
    0.6 to 0.9 V
    ETCS service data
    Fail Safe Drive
    [Fail #1]
    Whether or not fail safe function executed:
    OFF or ON
    ON: ETCS has failed
    ETCS service data
    Fail Safe Drive (Main CPU)
    [Fail #2]
    Whether or not fail safe function executed:
    OFF or ON
    ON: ETCS has failed
    ETCS service data
    ST1
    [ST1]
    Brake signal:
    OFF or ON
    ON: Brake pedal depressed
    -
    Throttle Position
    [Throttle Pos]
    Absolute throttle position sensor:
    Min.: 0 %, Max.: 100 %
    10 to 22 %: Idling
    75 to 95 %: Throttle fully open
    Calculated value based on VTA1
    Throttle Sensor Position
    [Throttle Pos]
    Throttle sensor positioning:
    Min.: 0 %, Max.: 100 %
    1. 0 %: Accelerator pedal released
    2. 64 to 96 %: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM
    Throttle Sensor Position #2
    [Throttle Pos #2]
    Throttle sensor positioning #2:
    Min.: 0 %, Max.: 100 %
    -
    Calculated value based on VTA2
    Throttle Position No. 1
    [Throttle Pos #1]
    Throttle position No. 1:
    Min.: 0 V, Max.: 5 V
    1. 0.2 to 1.0 V: Throttle fully closed
    2. 4.0 to 4.6 V: Throttle fully open
    ETCS service data
    Throttle Position No. 2
    [Throttle Pos #2]
    Throttle position No. 2:
    Min.: 0 V, Max.: 5 V
    1. 4.0 to 4.8 V: Throttle fully closed
    2. 0.2 to 1.0 V: Throttle fully open
    ETCS service data
    Throttle Position Command
    [Thrtl Comnd Val]
    Throttle position command value:
    Min.: 0 V, Max.: 4.9804 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    [Throttle Ssr #1]
    Throttle sensor opener position No. 1:
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    [Throttle Ssr #2]
    Throttle sensor opener position No. 2:
    Min.: 0 V, Max.: 4.9804 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1(AD)
    [Thrtl Ssr #1 AD]
    Throttle sensor opener position No. 1 (AD):
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    [Throttle Mot]
    Whether or not throttle motor control permitted:
    OFF or ON
    ON: Idling
    ETCS service data
    Throttle Motor
    [Throttle Mot]
    Throttle motor:
    Min.: 0 %, Max.: 100 %
    10 to 20 %: Idling
    ETCS service data
    Throttle Motor Duty (Open)
    [Thrtl Mot (Opn)]
    Throttle motor duty ratio (open):
    Min.: 0 %, Max.: 100 %
    0 to 40 %: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    [Thrtl Mot (Cls)]
    Throttle motor duty ratio (close):
    Min.: 0 %, Max.: 100 %
    0 to 40 %: Idling
    ETCS service data
    O2S B1 S1
    [O2S B1 S1]
    Heated oxygen sensor output voltage for bank 1 sensor 1:
    Min.: 0 V, Max.: 1.275 V
    0 to 1.0 V: Driving (50 km/h, 31 mph)
    Performing Inj Vol function of Active Test enables technician to check voltage output of sensor
    O2S B1 S2
    [O2S B1 S2]
    Heated oxygen sensor output voltage for bank 1 sensor 2:
    Min.: 0 V, Max.: 1.275 V
    0 to 1.0 V: Driving (50 km/h, 31 mph)
    Performing Inj Vol function of Active Test enables technician to check voltage output of sensor
    Short FT #1
    [Short FT #1]
    Short-term fuel trim of bank 1:
    Min.: -100 %, Max.: 99.2 %
    - 20 to 20 %
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    [Long FT #1]
    Long-term fuel trim of bank 1:
    Min.: -100 %, Max.: 99.2 %
    - 20 to 20 %
    Overall fuel compensation carried out in long-term to compensate continual deviation of short-term fuel trim from central value
    Fuel System Status (Bank1)
    [Fuel Sys #1]
    Fuel system status (Bank1):
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    CL: Idling after warming up
    OL (Open Loop): Has not yet satisfied conditions to go closed loop
    CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    OL FAULT: Open loop due to detected system fault
    CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
    Fuel System Status (Bank2)
    [Fuel Sys #2]
    Fuel system status (Bank2):
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    -
    -
    O2FT B1 S1
    [O2FT B1 S1]
    Short-term fuel trim associated with bank 1 sensor 1:
    Min.: -100 %, Max.: 99.2 %
    -20 to 20 %
    -
    Catalyst Temp (B1 S1)
    [Cat Temp B1S1]
    Catalyst temperature (Bank 1, Sensor 1):
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp (B1 S2)
    [Cat Temp B1S2]
    Catalyst temperature (Bank 1, Sensor 2):
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Initial Engine Coolant Temp
    [Ini Cool Temp]
    Initial engine coolant temperature:
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    [Ini Intake Temp]
    Initial intake air temperature:
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Injection Volume (Cylinder1)
    [Inj Vol]
    Injection volume (cylinder 1):
    Min.: 0 ml, Max.: 2.048 ml
    -
    -
    Starter Signal
    [Starter Sig]
    Starter signal:
    OFF or ON
    ON: Cranking
    -
    Starter Control
    [Starter Control]
    Starter switch status:
    OFF or ON
    ON: Cranking
    Cranking requirement signal from ignition switch or main body ECU
    Closed Throttle Position SW
    [Ctp SW]
    Closed throttle position switch (idling position switch):
    OFF or ON
    ON: Accelerator pedal released
    -
    A/C Signal
    [A/C Signal]
    A/C signal:
    OFF or ON
    ON: A/C ON
    -
    Neutral Position SW Signal
    [Pnp SW (NSW)]
    Park/neutral position switch signal status (NSW signal):
    OFF or ON
    -
    -
    Electrical Load Signal
    [Elect Load Sig]
    Electrical load signal:
    OFF or ON
    ON: Headlights or defogger turned ON
    -
    Stop Light Switch
    [Stop Light SW]
    Stop lamp switch:
    OFF or ON
    ON: Brake pedal depressed
    -
    +BM Voltage
    [+BM Voltage]
    +BM terminal voltage:
    Min.: 0 , Max.: 19.92182
    10 to 15 V: Idling
    -
    Battery Voltage
    [Batt]
    Battery voltage:
    Min.: 0 V, Max.: 65.535 V
    10 to 15 V: Idling
    -
    Actuator Power Supply
    [Actuator Power]
    Actuator power supply:
    OFF or ON
    ON: Idling
    ETCS service data
    EVAP Purge VSV
    [Evap (Purge) VSV]
    VSV status for EVAP control:
    OFF or ON
    -
    Active Test support data
    Fuel Pump/Speed Status
    [Fuel Pump / Spd]
    Fuel pump/speed status:
    OFF or ON
    -
    Active Test support data
    Electric Fan Motor
    [Fan Motor]
    Radiator fan motor status:
    OFF or ON
    -
    Active Test support data
    TC and TE1
    [TC/TE1]
    TC and TE1 terminals of DLC3:
    OFF or ON
    -
    Active Test support data
    VVT Aim Angle (Bank1)
    [VVTL Aim Angl#1]
    VVT aim angle (bank 1):
    Min.: 0 %, Max.: 100 %
    0 %: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle (Bank1)
    [VVT Chng Angl#1]
    VVT change angle:
    Min.: 0°FR, Max.: 60°FR
    0°FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty (Bank1)
    [VVT Ocv Duty B1]
    VVT OCV operation duty:
    Min.: 0 %, Max.: 100 %
    10 to 40 %: Idling
    Requested duty value for intrusive operation
    Idle Fuel Cut
    [FC Idl]
    Fuel cut idle:
    OFF or ON
    ON: Fuel cut operation
    FC IDL is ON when throttle valve fully closed and engine speed over 2,800 rpm
    Cylinder #1 Misfire Rate
    [Cyl #1]
    Misfire ratio of cylinder 1:
    Min.: 0 , Max.: 255
    0: No misfire
    Displayed only during idling
    Cylinder #2 Misfire Rate
    [Cyl #2]
    Misfire ratio of cylinder 2:
    Min.: 0 , Max.: 255
    0: No misfire
    Displayed only during idling
    Cylinder #3 Misfire Rate
    [Cyl #3]
    Misfire ratio of cylinder 3:
    Min.: 0 , Max.: 255
    0: No misfire
    Displayed only during idling
    All Cylinders Misfire Rate
    [Cyl All]
    All cylinders misfire rate:
    Min.: 0 , Max.: 255
    0 to 35
    -
    Misfire RPM
    [Misfire RPM]
    Engine RPM for first misfire range:
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    # Codes
    [# Codes]
    Number of codes:
    Min.: 0 , Max.: 255
    -
    Number of detected DTCs
    MIL ON Run Distance
    [MIL On Run Dist]
    MIL ON Run Distance:
    Min.: 0 km, Max.: 65535 km
    Distance after DTC detected
    -
    Running Time from MIL ON
    [MIL On Run Time]
    Running time from MIL ON:
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL ON
    -
    Engine Run Time
    [Eng Run Time]
    Engine run time:
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    -
    Time after DTC Cleared
    [Time DTC Clear]
    Time after DTC cleared:
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    [Dist DTC Clear]
    Distance after DTC cleared:
    Min.: 0 Km, Max.: 65535 Km
    Equivalent to drive distance after DTCs erased
    -
    Warmup Cycle Cleard DTC
    [Wu Cyc DTC clear]
    Warm-up cycle after DTC cleared:
    Min.: 0 , Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    Model Code
    [Model Code]
    Model code:
    KSP
    -
    Engine Type
    [Engine Type]
    Engine type:
    1KRFE
    -
    Cylinder Number
    [Cylinder Number]
    Number of cylinder
    3
    -
    Transmission Type
    [Transmission Type]
    Transmission type:
    MT or MMT
    -
    Destination
    [destination]
    Destination:
    W: Europe
    -
    Model Year
    [Model Year]
    Model year:
    Min.: 1900 MY, Max.: 2155 MY
    2005
    -
    System Identification
    [System Identification]
    System identification:
    Gasoline
    -


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time. Data Lists can be displayed during Active Tests.

  1. Connect an intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn the tester ON.

  4. Select the following menu items: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Test by referring to the table below.

    Items
    [Abbreviation]
    Test Details
    Control Ranges
    Diagnostic Note
    Control the Injection Volume
    [Inj Vol]
    Change injection volume
    Between -12.5 % and 24.8 %
    1. All injectors tested at same time
    2. Perform test at less than 3,000 rpm
    3. Injection volume can be changed in 1 % graduations within control range
    Control the Injection Volume for A/F Sensor
    [A/F Control]
    Change injection volume
    Lower by 12.5 % or increase by 24.8 %
    1. Perform test at less than 3,000 rpm
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of Heated Oxygen (HO2) sensor voltage outputs
    3. To conduct test, select following menu items: Active Test / Control the Injection Volume for A/F Sensor / User Data / O2S B1S1 and O2S B1S2
    Activate the VSV for Evap Control
    [Evap VSV (Alone)]
    Activate EVAP VSV control
    ON/OFF
    Only EVAP VSV is commanded during this test
    Control the Fuel Pump / Speed
    [Fuel Pump / Spd]
    Fuel pump speed control
    ON (low speed) / OFF (high speed)
    Test possible when following conditions met:
    1. Ignition switch on (IG)
    2. Engine is stopped
    Connect the TC and TE1
    [TC/TE1]
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1disconnected
    Control the Idle Fuel Cut Prohibit
    [FC Idl Prohbt]
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    [Cooling Fan]
    Control Electric Cooling Fan
    ON/OFF
    Test possible when following conditions met:
    1. Ignition switch on (IG)
    2. Engine is stopped
    Activate the ACC Cut Relay
    [ACC Cut]
    Active ACC cut relay
    ON/OFF
    Test possible when following conditions met:
    1. Ignition switch on (IG)
    2. Engine is stopped
    Activate the Starter Relay
    [Starter]
    Starter
    ON/OFF
    -
    Control the Cylinder#1 Fuel Cut
    [Fuel Cut #1]
    Cylinder #1 injector fuel cut
    ON/OFF
    Same as above
    Control the Cylinder#2 Fuel Cut
    [Fuel Cut #2]
    Cylinder #2 injector fuel cut
    ON/OFF
    Same as above
    Control the Cylinder#3 Fuel Cut
    [Fuel Cut #3]
    Cylinder #3 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling.
    Control the VVT Linear (Bank1)
    [VVT Linear B1]
    Control VVT (bank 1)
    -128 to 127% OCV control duty ratio can be set to any value within this range
    100%: Maximum advance
    -100%: Maximum retard
    Engine stall or rough idle when VVT actuator operated by 100 %.
    Test possible during idle.
    Control the VVT System (Bank1)
    [VVT Ctrl B1]
    Control VVT (bank 1)
    ON/OFF
    Engine stalls or idles roughly when OCV turned on
    Normal engine running or idling when OCV off
    Test possible while vehicle stopped and engine idling

← FAIL-SAFE CHART (from Aug 2005)DIAGNOSTIC TROUBLE CODE CHART (Aug 2005 – Oct 2005) →