2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2005 – Dec 2005

Versions by build date: Aug 2005 – Dec 2005 from Jan 2006


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


10. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A108951
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.


11. REMOVE COWL TOP PANEL OUTER

A117320
  1. Disengage the wire harness clamp.

  1. A107444
    Remove the 9 bolts and remove the cowl top panel outer.


12. REMOVE BATTERY

13. REMOVE BATTERY TRAY

14. REMOVE FRONT WHEEL RH

15. REMOVE ENGINE UNDER COVER RH

16. DRAIN ENGINE OIL

17. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.

    A106596E01


18. REMOVE CYLINDER HEAD COVER NO. 2

A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.


19. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE NO. 1

A115124
  1. Disconnect fuel vapor feed hose No. 1 and fuel vapor feed hose No. 2 from the vacuum switching valve assembly.

  1. Disconnect the vacuum switching valve assembly connector and wire harness clamp.

  1. A115123
    Disconnect ventilation hose No. 2.

  1. A115125
    Disconnect the wire harness clamp and mass air flow meter connector.

  1. A115126
    Loosen the hose clamp, unlock the air cleaner assembly clamp and remove air cleaner cap sub-assembly with air cleaner hose No. 1.


20. DISCONNECT RADIATOR HOSE NO. 3

A116580
  1. Disconnect radiator hose No. 3.


21. DISCONNECT RESERVE TANK HOSE

A116581
  1. Disconnect the reserve tank hose.


22. REMOVE WATER FILLER SUB-ASSEMBLY

A116739
  1. Separate radiator hose No. 1 from the cylinder head.

  1. Remove the 2 nuts and remove the water filler sub-assembly.


23. DISCONNECT WATER BY-PASS HOSE NO. 2

A116740
  1. Disconnect water by-pass hose No. 2.


24. DISCONNECT WATER BY-PASS HOSE

A116741
  1. Disconnect the water by-pass hose.


25. DISCONNECT THROTTLE WITH MOTOR BODY CONNECTOR

A116742
  1. Separate the wire harness clamp.

  1. Remove the nut and separate the throttle with motor body connector.


26. DISCONNECT VENTILATION HOSE

A116743
  1. Disconnect the ventilation hose.


27. DISCONNECT UNION TO CONNECTOR TUBE HOSE

A116744
  1. Disconnect the union to connector tube hose.


28. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY

29. REMOVE INTAKE MANIFOLD

A116745
  1. Separate the wire harness clamps shown in the illustration.

  1. A116746
    Remove the 3 bolts and 2 nuts and remove the intake manifold.


30. REMOVE OIL LEVEL GAUGE GUIDE

A116747
  1. Remove the wire harness clamp and the bolt and remove the oil level gauge guide.


31. DISCONNECT FUEL TUBE SUB-ASSEMBLY

A115492
  1. Remove the fuel pipe clamp.

  1. A117474E01
    Pinch the retainer of the fuel tube connector, then pull out the fuel tube connector to disconnect the fuel tube from the fuel delivery pipe sub-assembly.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting as the fuel tube connector has the O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.


32. DISCONNECT BOOSTER VACUUM TUBE

A116748
  1. Disconnect the booster vacuum tube.


33. DISCONNECT CAMSHAFT POSITION SENSOR CONNECTOR

A116749
  1. Disconnect the camshaft position sensor connector.


34. DISCONNECT ENGINE COOLANT TEMPERATURE SENSOR CONNECTOR

A116750
  1. Disconnect the engine coolant temperature sensor connector.


35. DISCONNECT HEATED OXYGEN SENSOR CONNECTOR

A116751
  1. Remove the bolts and separate the sensor bracket.

  1. Disconnect the heated oxygen sensor connector.


36. DISCONNECT HEATER WATER INLET HOSE A

A116752
  1. Disconnect heater water inlet hose A.


37. SEPARATE WATER BY-PASS PIPE NO. 1

A116753
  1. Remove the bolt and separate water by-pass pipe No. 1.


38. DISCONNECT WIRE HARNESS

A116755
  1. Remove the 2 bolts and disconnect the wire harness.


39. SEPARATE EXHAUST PIPE ASSEMBLY FRONT

A116756
  1. Remove the 2 bolts and 2 compression springs and separate the exhaust pipe assembly front.


40. REMOVE MANIFOLD SUPPORT BRACKET

A116757
  1. Remove the 3 bolts and remove the manifold support bracket.


41. REMOVE FAN AND GENERATOR V BELT

  1. A116197E01
    Loosen bolts A and B.

  1. Release the fan and generator V belt tension and remove the fan and generator V belt.


42. REMOVE GENERATOR ASSEMBLY

A115418
  1. Remove the terminal cap.

  1. Separate the connector and harness clamp.

  1. Remove the nut and remove terminal B.

  1. A115419E01
    Remove fan belt adjusting slider fixing bolts A and B and remove the fan belt adjusting slider.

  1. A115420E01
    Remove fixing bolt B and remove the generator.


43. REMOVE IGNITION COIL NO. 1

A115484
  1. Disconnect the 4 ignition coil connectors.

  1. A115485
    Remove the 4 bolts and 4 ignition coils.


44. REMOVE VENTILATION HOSE

A115487
  1. Disconnect the ventilation hose.


45. REMOVE VENTILATION HOSE NO. 2

A115488
  1. Disconnect ventilation hose No. 2.


46. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A115489
  1. Disconnect the fuel injector connectors.

  1. A116181
    Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.

  1. A066472E01
    Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.


47. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A116236
  1. Place a wooden block on a jack underneath the engine.

  1. G100143
    Remove the 5 bolts and nut and remove the engine mounting insulator sub-assembly RH.


48. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

A116203E01

  1. Set cylinder No. 1 to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.

    2. A116204E01
      Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.

  1. A116552E01
    Using 2 SSTs, loosen the bolt while holding the crankshaft damper sub-assembly.
    SST
    09213-14010   (91651-60865)
    09330-00021  

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SSTs and the bolt.

  1. Remove the crankshaft damper sub-assembly.


49. REMOVE CRANKSHAFT POSITION SENSOR

A091817
  1. Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and remove the crankshaft position sensor.


50. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

A116177
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. A116178
    Remove the bolt and nut and remove the camshaft timing oil control valve assembly.

  1. A116179
    Remove the O-ring from the camshaft timing oil control valve assembly.


51. REMOVE WATER PUMP PULLEY

A116191E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and remove the water pump pulley.


52. REMOVE WATER PUMP ASSEMBLY

A116192
  1. Remove the 3 bolts and 2 nuts and remove the water pump assembly and gasket.


53. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A116553
  1. Remove the 4 bolts and remove the transverse engine engine mounting bracket.


54. REMOVE OIL PUMP ASSEMBLY

A116554
  1. Remove the 15 bolts and the nut.

  1. A116555
    Using a screwdriver with its tip wrapped in protective tape, prize the oil pump assembly to remove it.

    NOTICE:
    Do not damage the contact surfaces of the oil pump assembly or oil pan sub-assembly.

  1. A116556
    Remove the 2 O-rings from the cylinder block and oil pan sub-assembly.


55. REMOVE OIL PUMP SEAL

A035281
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pump seal.


56. REMOVE CHAIN TENSIONER ASSEMBLY NO. 1

NOTICE:
  1. Do not rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40 ° from the TDC first.

  1. A116564E01
    Pull up the stopper plate and hold it with its lock released.

  1. A116565E01
    Unlock the plunger of the tensioner and push it in to the end.

  1. A116566E01
    Pull down the stopper plate with the plunger pushed to the end and lock the plunger.

  1. A116567
    Insert a 3 mm (0.12 in.) diameter bar into the hole in the stopper plate and lock the plunger.

  1. A116568
    Remove the 2 bolts and remove chain tensioner assembly No. 1.


57. REMOVE CHAIN TENSIONER SLIPPER

A116569
  1. Remove the chain tensioner slipper.


58. REMOVE CHAIN VIBRATION DAMPER NO. 1

A116570
  1. Remove the 2 bolts and remove chain vibration damper No. 1.


59. REMOVE CHAIN SUB-ASSEMBLY

60. REMOVE CAMSHAFT

NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A035758E01
    Using several steps, loosen and remove the 19 bearing cap bolts uniformly in the sequence shown in the illustration, and then remove camshaft bearing cap No. 1 and camshaft bearing cap No. 2.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.

  1. Remove the camshaft and camshaft No. 2.


61. REMOVE CYLINDER HEAD SUB-ASSEMBLY

A035286
  1. Using several steps, loosen and remove the 10 cylinder head bolts uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 cylinder head bolts and the plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing the bolts in the wrong order.


62. REMOVE CYLINDER HEAD GASKET

A116758
  1. Remove the cylinder head gasket.


63. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO. 1

A116759
  1. Remove the 4 bolts and remove exhaust manifold heat insulator No. 1.


64. REMOVE EXHAUST MANIFOLD

A116761
  1. Remove the 3 bolts and 2 nuts and remove the exhaust manifold.


65. REMOVE HARNESS BRACKET

A116762
  1. Remove the bolt and remove the harness bracket.


66. REMOVE BOOSTER VACUUM TUBE

A116763
  1. Remove the 2 bolts and remove the booster vacuum tube.


67. REMOVE CAMSHAFT POSITION SENSOR

A116764
  1. Remove the bolt and remove the camshaft position sensor.


68. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

A116765E01
  1. Using SST, remove the engine coolant temperature sensor connector.

    SST
    09817-33190  


69. REMOVE WATER BY-PASS HOSE

A116766
  1. Remove the water by-pass hose.


70. REMOVE HARNESS BRACKET

A116767
  1. Remove the bolt and remove the harness bracket.


71. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

A116768
  1. Remove the 3 bolts and remove the fuel delivery pipe sub-assembly together with the 4 fuel injectors.

    NOTICE:
    Do not drop the fuel injectors when removing the fuel delivery pipe sub-assembly.


72. REMOVE FUEL INJECTOR ASSEMMBLY

A115498E01
  1. Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.


73. REMOVE DELIVERY PIPE NO. 1 SPACER

A116955
  1. Remove the 2 delivery pipe No. 1 spacers.


74. REMOVE INJECTOR VIBRATION INSULATOR

A116956
  1. Remove the 4 injector vibration insulators.

← COMPONENTS (from Jan 2006)REMOVAL (from Jan 2006) →