2005-2008 Yaris · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Aug 2005


1. REMOVE INTAKE VALVE GUIDE BUSH

A001067E02
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A037110E02
    Using SST and a hammer, tap out the guide bushing.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


2. REMOVE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap out the guide bushing.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


3. INSTALL INTAKE VALVE GUIDE BUSH

A001445E01
  1. Using a caliper gauge, measure the bushing bore diameter of the cylinder head.

    Inside diameter:
    9.685 to 9.706 mm (0.3813 to 0.3821 in.)

    If the bushing bore diameter of the cylinder head is greater than 9.706 mm (0.3821 in.), machine the bushing bore to the dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.)
    Bushing bore diameter
    mm (in.)
    Bushing size
    9.685 to 9.706
    (0.3813 to 0.3821)
    STD
    9.735 to 9.755
    (0.3833 to 0.3841)
    O/S 0.05

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. A080977E02
    Using SST and a hammer, tap a new guide bushing in to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.0 to 9.4 mm (0.354 to 0.370 in.)

  1. A001447E02
    Using a sharp 5 mm reamer, ream the guide bushing to obtain the standard oil clearance between the guide bushing and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)


4. INSTALL EXHAUST VALVE GUIDE BUSH
  1. Using a caliper gauge, measure the bushing bore diameter of the cylinder head.

    Inside diameterr:
    9.685 to 9.706 mm (0.3813 to 0.3821 in.)

    If the bushing bore diameter of the cylinder head is greater than 9.706 mm (0.3821 in.), machine the bushing bore to the dimension of 9.735 to 9.755 mm (0.3833 to 0.3841 in.)
    Bushing bore diameter
    mm (in.)
    Bushing size
    9.685 to 9.706
    (0.3813 to 0.3821)
    STD
    9.735 to 9.755
    (0.3833 to 0.3841)
    O/S 0.05

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap a new guide bushing in to the specified protrusion height.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.0 to 9.4 mm (0.354 to 0.370 in.)

  1. Using a sharp 5 mm reamer, ream the guide bushing to obtain the standard oil clearance between the guide bushing and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)

← INSPECTION (from Aug 2005)REASSEMBLY (from Aug 2005) →