2005-2008 Yaris · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

A080980E02
  1. Using a plastic-faced hammer, tap a new ring pin in to the specified protrusion height.

    Protrusion height:
    8.5 to 9.5 mm (0.335 to 0.374 in.)


2. INSTALL STUD BOLT

  1. Using "Torx" socket wrenches E5 and E7, install the 7 stud bolts.

    Torque:
    Bolt A:
    10 N*m (102 kgf*cm, 7.4 ft.*lbf)
    Bolt B:
    4.0 N*m (41 kgf*cm, 35 in.*lbf)
    Bolt C:
    10 N*m (102 kgf*cm, 7.4 ft.*lbf)
    Bolt D:
    9.0 N*m (92 kgf*cm, 80 in.*lbf)


    A050180E03


3. INSTALL VALVE STEM OIL SEAL

A050182E02
  1. Apply a light coat of engine oil to the valve stem.

    NOTICE:
    Installing the oil seal for intake and exhaust onto the opposite valve guide bush may cause failures.

    HINT:
    The intake valve oil seal is gray and the exhaust valve oil seal is black.

  1. A001063E02
    Using SST, push in a new oil seal.
    SST
    09201-41020  


4. INSTALL INTAKE VALVE

A001065E01
  1. Install the valve, spring seat, valve spring, and spring retainer.

    NOTICE:
    Reinstall the parts in their original locations in the original order.

  1. A037109E03
    Using SST, compress the valve spring and place the 2 retainer locks around the valve stem.
    SST
    09202-70020   (09202-00010)

  1. A007307E01
    Using a plastic-faced hammer and the valve stem (not in use) with its tip wrapped in tape, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.


5. INSTALL EXHAUST VALVE
  1. Install the valve, spring seat, valve spring, and spring retainer.

  1. Using SST, compress the valve spring and place the 2 retainer locks around the valve stem.

    SST
    09202-70020   (09202-00010)

  1. Using a plastic-faced hammer and the valve stem (not in use) with the tip wrapped in tape, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Do not damage the valve stem tip.


6. INSTALL OIL CONTROL VALVE FILTER (for Unleaded Gasoline Specification Vehicle)
  1. Install the filter into the with head taper screw plug No. 2.


7. INSTALL WITH HEAD TAPER SCREW PLUG NO. 2
  1. Using an 8 mm hexagon wrench, install the taper screw plug and a new gasket.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


8. INSTALL VALVE LIFTER
  1. Apply a light coat of engine oil to the valve lifter.

  1. Install the valve lifter.

  1. Check that the valve lifter rotates smoothly by hand.


9. INSTALL WITH HEAD TAPER SCREW PLUG NO. 1

A062890E01
  1. Using a 10 mm socket hexagon wrench, install the taper screw plug with a new gasket.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

← REPLACEMENT (from Aug 2005)INSTALLATION (Aug 2005 – Dec 2005) →