2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT WIPER SWITCH (for LHD, RHD Europe)

E109077E01
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Front Wiper Switch:
      Tester Connection
      Condition
      Specified Condition
      +B (B-2) - +1 (B-3)
      MIST
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      OFF
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      INT
      Below 1 Ω
      +B (B-2) - +1 (B-3)
      LO
      Below 1 Ω
      +B (B-2) - +2 (B-4)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Front Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WF (A-3)
      OFF
      10 kΩ or higher
      EW (A-2) - WF (A-3)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance (for TMC Made):
      Rear Wiper and Washer Switch (w/ Intermittent):
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WR (B-5)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      EW (A-2) - C1R (A-6)
      OFF
      10 kΩ or higher
      C1R (A-6) - EW (A-2)
      LO
      Below 1 Ω
      EW (A-2) - +1R (A-7)
      HI
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      +1R (A-7) - WR (B-5)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the windshield wiper switch.

      Standard Resistance (for TMMF Made):
      Rear Wiper and Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WR (B-5)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      EW (A-2) - C1R (A-6)
      +1R (A-7) - WR (B-5)
      OFF
      10 kΩ or higher
      C1R (A-6) - EW (A-2)
      ON
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      +1R (A-7) - WR (B-5)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the windshield wiper switch.

      Standard Resistance (for TMC Made):
      Rear Wiper and Washer Switch (w/o Intermittent):
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WR (B-5)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      OFF
      10 kΩ or higher
      EW (A-2) - +1R (A-7)
      ON
      Below 1 Ω
      EW (A-2) - WR (B-5)
      EW (A-2) - +1R (A-7)
      +1R (A-7) - WR (B-5)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 2 (EW) of the A connector and 1 (+S) of the B connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 1 (+S) of the B connector for 5 seconds.

    5. Connect the negative (-) battery lead to terminal 1 (+S) of the B connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.


      E106356E05
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 1 (+S) of the B connector and 2 (EW) of the A connector.

    3. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      E106382E02
      If the result is not as specified, replace the windshield wiper switch.


INSPECT WIPER SWITCH (for RHD except Europe)

E114461E01
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Front Wiper Switch:
      Tester Connection
      Condition
      Specified Condition
      +B (A-3) - +1 (A-2)
      MIST
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      OFF
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      INT
      Below 1 Ω
      +B (A-3) - +1 (A-2)
      LO
      Below 1 Ω
      +B (A-3) - +2 (A-1)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Front Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (B-2) - WF (B-1)
      OFF
      10 kΩ or higher
      EW (B-2) - WF (B-1)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Rear Wiper and Washer Switch:
      Tester Connection
      Condition
      Specified Condition
      EW (B-2) - WR (A-10)
      WASH (Rear wiper switch OFF)
      Below 1 Ω
      EW (B-2) - WR (A-10)
      EW (B-2) - 1R (B-4)
      OFF
      10 kΩ or higher
      EW (B-2) - +1R (B-4)
      ON
      Below 1 Ω
      EW (B-2) - WR (A-10)
      EW (B-2) - +1R (B-4)
      +1R (B-4) - WR (A-10)
      WASH (Rear wiper switch ON)
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 4 (+S) of the A connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 4 (+S) of the A connector for 5 seconds.

    5. Connect the negative (-) battery lead to terminal 4 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      Standard:
      Refer to the illustration below.


      E106356E06
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 4 (+S) of the A connector and 2 (EW) of the B connector.

    3. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector. Turn the washer switch on and off, and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      E106382E03
      If the result is not as specified, replace the windshield wiper switch.

← REMOVAL (from Aug 2005)INSTALLATION (from Aug 2005) →