2005-2008 Yaris · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Jan 2006


INSPECT WIPER SWITCH (for LHD)

E109077E01
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      +B (B-2) - +1 (B-3)
      MIST
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      OFF
      Below 1 Ω
      +S (B-1) - +1 (B-3)
      INT
      Below 1 Ω
      +B (B-2) - +1 (B-3)
      LO
      Below 1 Ω
      +B (B-2) - +2 (B-4)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EW (A-2) - WF (A-3)
      OFF
      10 kΩ or higher
      EW (A-2) - WF (A-3)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 2 (EW) of the A connector and 1 (+S) of the B connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 1 (+S) of the B connector for 5 seconds.

    5. Connect the negative (-) battery lead to terminal 1 (+S) of the B connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      Standard:
      Refer to the illustration below.


      E129662E01
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 2 (+B) of the B connector and the negative (-) battery lead to terminals 1 (+S) of the B connector and 2 (EW) of the A connector.

    3. Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the B connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the A connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the B connector and 2 (EW) of the A connector.

      E129663E01
      If the result is not as specified, replace the windshield wiper switch.


INSPECT WIPER SWITCH (for RHD)

E114461E01
  1. Check the resistance.

    1. Measure the resistance and check the results in accordance with the value(s) in the tables below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      +B (A-3) - +1 (A-2)
      MIST
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      OFF
      Below 1 Ω
      +S (A-4) - +1 (A-2)
      INT
      Below 1 Ω
      +B (A-3) - +1 (A-2)
      LO
      Below 1 Ω
      +B (A-3) - +2 (A-1)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EW (B-2) - WF (B-1)
      OFF
      10 kΩ or higher
      EW (B-2) - WF (B-1)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.

  1. Check the intermittent operation.

    1. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 4 (+S) of the A connector.

    3. Turn the wiper switch to the INT position.

    4. Connect the positive (+) battery lead to terminal 4 (+S) of the A connector for 5 seconds.

    5. Connect the negative (-) battery lead to terminal 4 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      Standard:
      Refer to the illustration below.


      E129662E03
      If the result is not as specified, replace the windshield wiper switch.

  1. Check the operation (front washer).

    1. Turn the wiper switch off.

    2. Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 4 (+S) of the A connector and 2 (EW) of the B connector.

    3. Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector. Turn the washer switch on and off, and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

      E129663E02
      If the result is not as specified, replace the windshield wiper switch.

← REMOVAL (from Jan 2006)INSTALLATION (from Jan 2006) →