2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL GENERATOR ASSEMBLY

A128376E01
  1. Provisionally install the generator with fixing bolt C.

  1. A128375E01
    Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolt A and nut B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for Bolt B

  1. A128374
    Install the connector.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


2. INSTALL FAN AND GENERATOR V BELT
  1. Temporarily install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Before installing the V belt, check each pulley for any kind of liquid and chips.
    1. Check that the ribs of the V belt are correctly fitted into the grooves of the pulleys.


3. ADJUST FAN AND GENERATOR V BELT

  1. A098655
    Insert a bar between the generator and the engine. Pull the bar toward the front of the vehicle and adjust the tension.

  1. A098654E01
    Tighten bolt A, then tighten bolt B.

    Torque:
    Bolt A:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


4. INSTALL ENGINE WIRE

A128373
  1. Install the engine wire with the 2 bolts.

    Torque:
    3.8 N*m{ 39 kgf*cm , 34 in.*lbf }

  1. Connect the camshaft position sensor connector.


5. INSPECT FAN AND GENERATOR V BELT
  1. Inspect the fan and generator V belt deflection.

    Pressing force:
    98 N (10kgf, 221 lbf)

    New belt
    mm (in.)
    Used belt
    mm (in.)
    5.0 to 6.0
    (0.197 to 0.236)
    7.0 to 8.5
    (0.276 to 0.335)

  1. Inspection the fan and generator V belt tension.

    New belt
    mm (in.)
    Used belt
    mm (in.)
    980 to 1176
    (100 to 120, 220 to 264)
    490 to 686
    (50 to 70, 110 to 154)

    NOTICE:
    1. Check the V belt deflection at the specified point.
    1. When installing a new belt, set its tension value as specified.
    1. When checking a belt used for over 5 minutes, confirm that the deflection value is within the specified range for a used belt.
    1. When reinstalling a belt used for over 5 minutes, check whether its deflection value is within the specified range for the used belt.
    1. When using a belt tension gauge, confirm its accuracy first by using a master gauge.


6. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.


7. INSTALL ENGINE UNDER COVER
  1. Provisionally install the engine under cover with the 5 bolts, 4 screws and 2 clips.

  1. Tighten the 4 screws.

  1. Tighten the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REASSEMBLY (from Nov 2005)PRECAUTION (from Aug 2005) →