2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL RADIATOR RESERVE TANK HOSE GROMMET

2. INSTALL RADIATOR SUPPORT CUSHION

3. INSTALL FAN SHROUD

4. INSTALL WATER FILLER BRACKET

A104368
  1. Connect the 2 hoses.

  1. A104369
    Install the water filler bracket with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


5. INSTALL RADIATOR ASSEMBLY
  1. Install the radiator assembly onto the vehicle.

  1. A117372
    Engage the clamp and connect the fan motor connector.

  1. Engage the 3 clamps for the oxygen sensor wire harness.


6. INSTALL COOLER CONDENSER ASSEMBLY (w/ Air Conditioning System)

A104371E01
  1. Engage the 2 guides and install the cooler condenser with the 2 claws.


7. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A104367
  1. Install the radiator support with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. A104375
    Connect the horn connector.


8. INSTALL HOOD LOCK ASSEMBLY

A108456
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A108455
    Connect the hood lock control cable assembly to the clamp.


9. CONNECT RADIATOR HOSE NO. 2

A104373
  1. Connect radiator hose No. 2 with the clip.


10. CONNECT RADIATOR HOSE NO. 1

A104372
  1. Connect radiator hose No. 1 with the clip.


11. INSTALL COOLER COVER NO. 1 (w/ Air Conditioning System)

A104376
  1. Install cooler cover No. 1 with the 2 clips.


12. INSTALL RADIATOR SIDE AIR SEAL NO. 1

A104379E01
  1. Engage the 2 claws and install radiator side air seal No. 1.


13. INSTALL RADIATOR SIDE AIR SEAL NO. 2

A104378E01
  1. Engage the 2 claws and install radiator side air seal No. 2.


14. INSTALL RADIATOR SUPPORT ABSORBER UPPER

  1. B114368
    Engage the 6 claws and install the radiator support upper absorber.


15. INSTALL FRONT BUMPER COVER

  1. B119954
    w/ Front Spoiler:

    1. Install the 2 clips and the 4 screw grommets.

  1. B114362
    w/o Front Spoiler:

    1. Install the 2 clips and the screw grommet.

  1. w/ Fog Light:

    1. B117704
      Connect the 2 fog light connectors.

    2. Engage the 6 claws and install the front bumper cover.

  1. B117705
    w/o Fog Light:

    1. Engage the 6 claws and install the front bumper cover.

  1. B119955
    w/ Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 3 screws.

  1. B117706
    w/o Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 8 screws.

  1. B114359E01
    Remove the protective tape.


16. INSTALL FRONT SPOILER COVER (w/ Front Spoiler)

  1. B119935
    Install the front spoiler cover with the 4 screws.


17. INSTALL FRONT SPOILER COVER LH (w/ Front Spoiler)

  1. B119951
    Install the front spoiler cover with the 5 screws.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


19. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Disconnect the vinyl hose.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    4.5 liters (4.8 USqts, 4.2 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


20. ADJUST HOOD LOCK ASSEMBLY
  1. Loosen the 3 bolts.

  1. Adjust the hood lock position so that the striker can enter it smoothly.

  1. Tighten the 3 bolts after the adjustment.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


21. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A107403
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.

← REMOVAL (from Aug 2005)ON-VEHICLE INSPECTION (from Nov 2005) →