REMOVAL
Removal / installation · Vehicles built from Aug 2005
- CAUTION:
- Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN ENGINE COOLANT |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Install a vinyl hose onto the radiator side.

Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.
Loosen the water drain plug, then drain the coolant.


| 3. REMOVE FRONT SPOILER COVER LH (w/ Front Spoiler) |
Remove the 5 screws and the front spoiler cover.

| 4. REMOVE FRONT SPOILER COVER (w/ Front Spoiler) |
Remove the 4 screws and the front spoiler cover.

| 5. REMOVE FRONT BUMPER COVER |
Apply protective tape as shown in the illustration.

w/ Front Spoiler:

Remove the 3 screws.
Remove the 2 screw grommets.
Remove the 7 clips.
w/o Front Spoiler:

Remove the 8 screws.
Remove the 2 screw grommets.
Remove the 7 clips.
w/ Fog Light:

Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.
Disconnect the 2 fog light connectors.
w/o Fog Light:

Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.
w/ Front Spoiler:

Remove the 2 clips and the 4 screw grommets.
w/o Front Spoiler:

Remove the 2 clips and the screw grommet.
| 6. REMOVE RADIATOR SUPPORT ABSORBER UPPER |
Using a screwdriver, disengage the 6 claws and remove the radiator support upper absorber.

| 7. REMOVE RADIATOR SIDE AIR SEAL NO. 2 |
![]() ![]() |
Disengage the 2 claws and remove radiator side air seal No. 2.
| 8. REMOVE RADIATOR SIDE AIR SEAL NO. 1 |
![]() ![]() |
Disengage the 2 claws and remove radiator side air seal No. 1.
| 9. REMOVE COOLER COVER NO.1 (w/ Air Conditioning System) |
![]() ![]() |
Remove the 2 clips and cooler cover No. 1.
| 10. DISCONNECT RADIATOR HOSE NO.1 |
![]() ![]() |
Loosen the clip and disconnect radiator hose No. 1.
| 11. DISCONNECT RADIATOR HOSE NO.2 |
![]() ![]() |
Loosen the clip and disconnect radiator hose No. 2.
| 12. REMOVE HOOD LOCK ASSEMBLY |
![]() ![]() |
Separate the hood lock control cable assembly from the 2 clamps.
Remove the 3 bolts and remove the hood lock assembly.

| 13. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY UPPER |
![]() ![]() |
Separate the horn connector.
Remove the 4 bolts and remove the radiator support.

| 14. SEPARATE COOLER CONDENSER ASSEMBLY (w/ Air Conditioning System) |
![]() ![]() |
Disengage the 2 claws and separate the cooler condenser from the radiator.
| 15. REMOVE RADIATOR ASSEMBLY |
![]() ![]() |
Separate the clamp and separate the fan motor connector.
Disengage the 3 clamps for the oxygen sensor wire harness.
Remove the radiator assembly from the vehicle.
| 16. REMOVE WATER FILLER BRACKET |
![]() ![]() |
Remove the 2 bolts and separate the water filler bracket.
Separate the radiator reserve tank hose.

Separate radiator hose No. 3.
| 17. REMOVE FAN SHROUD |
| 18. REMOVE RADIATOR SUPPORT CUSHION |
| 19. REMOVE RADIATOR RESERVE TANK HOSE GROMMET |










