2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2006


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. REMOVE BATTERY
  1. Disconnect the cable from the battery terminal.

  1. Loosen the nut and remove the battery clamp.

  1. Remove the battery.


3. REMOVE BATTERY TRAY

4. REMOVE FRONT WHEELS

5. REMOVE ENGINE UNDER COVER LH

6. REMOVE ENGINE UNDER COVER RH

7. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, then drain the coolant.

    A147622E02


8. DRAIN MANUAL TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


9. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


10. REMOVE FRONT WIPER ARM LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


11. REMOVE FRONT WIPER ARM RH

HINT:
Use the same procedure as for the LH side.


12. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


14. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


15. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


16. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


17. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


18. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Disengage the claw and remove the No. 2 cowl to register duct sub-assembly.


19. REMOVE COWL TOP PANEL OUTER

A108438
  1. Disengage the wire harness clamp.

  1. A115392
    Remove the 9 bolts and remove the cowl top panel outer.


20. REMOVE AIR CLEANER ASSEMBLY

A147547E01
  1. Separate the intake air flow meter connector and wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Unfasten the 2 clamps.

  1. Remove the air cleaner cap sub-assembly with air cleaner hose.

  1. Remove the air cleaner element.

  1. A104895
    Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet.


21. REMOVE AIR CLEANER BRACKET

A117308
  1. Separate the wire harness clamp from the air cleaner bracket.

  1. Remove the 2 bolts and remove the air cleaner bracket.


22. REMOVE BATTERY CARRIER

A117309
  1. Separate the wire harness clamp from the battery carrier.

  1. Remove the 5 bolts and remove the battery carrier.


23. REMOVE NO. 2 CYLINDER HEAD COVER

  1. A163755
    Disengage the 2 fittings shown in the illustration.

  1. A163756
    Disengage the 2 fittings shown in the illustration, then remove the No. 2 cylinder head cover.


24. REMOVE FAN AND GENERATOR V BELT

  1. A147659E01
    Loosen bolts A and B.

  1. Turn adjusting bolt C to release the tension and remove the V belt from the pulleys.

  1. Remove the fan and generator V belt.


25. REMOVE NO. 2 RADIATOR HOSE

  1. A147548
    Loosen the 2 clips and remove the No. 2 radiator hose.


26. REMOVE FRONT BUMPER COVER

  1. B160160E01
    Apply protective tape as shown in the illustration.

  1. B160097
    Remove the 5 screws and the 3 bolts.

  1. Remove the 2 screw grommets.

  1. B160161
    Remove the 7 clips.

  1. B160099E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the 2 fog light connectors.

  1. B160102
    Remove the 2 clips, the 2 spring nuts and the screw grommet.


27. DISCONNECT NO. 1 RADIATOR HOSE

A147631
  1. Loosen the clip and disconnect the No. 1 radiator hose.


28. REMOVE HOOD LOCK ASSEMBLY

A108455
  1. Separate the hood lock control cable assembly from the 2 clamps.

  1. A108456
    Remove the 3 bolts and remove the hood lock assembly.


29. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A147633
  1. Disconnect the horn connector.

  1. A147634
    Remove the 4 bolts and remove the radiator support sub-assembly upper.


30. REMOVE FAN SHROUD VENTILATION DUCT ASSEMBLY

A147636
  1. Disengage the 4 claws and remove the fan shroud ventilation duct assembly.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.


31. REMOVE RADIATOR ASSEMBLY

A147635
  1. Separate the cooling fan motor connector and wire harness clamp.

  1. A147637
    Disengage the 2 claws and remove the radiator assembly from the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.


32. SEPARATE WITH PULLEY COMPRESSOR ASSEMBLY

I103380
  1. Disconnect the connector and the clamp.

  1. Remove the 2 bolts and 2 nuts.

  1. I103381
    Using "TORX" socket wrench E8, remove the 2 stud bolts and compressor.


33. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

C115305
  1. Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.


34. SEPARATE UNION TO CHECK VALVE HOSE

  1. A147549
    Loosen the clip and separate the union to check valve hose.


35. SEPARATE NO. 1 FUEL VAPOR FEED HOSE

  1. A147550
    Separate the No. 1 fuel vapor feed hose from the vacuum switching valve assembly.


36. DISCONNECT ENGINE WIRE

  1. A147551
    Remove the bolt and separate the transaxle earth wire.

  1. Separate the 2 wire harness clamps.

  1. A147552
    Disconnect the 2 connectors.

  1. A147554
    Pull up the lever and disconnect the connector from the engine control computer.

  1. Separate the wire harness clamps.

  1. A147553
    Remove the 2 connectors and clamp from the engine room junction block and disconnect the wire harness.

  1. Disconnect all wire harnesses and connectors.

    NOTICE:
    Make sure that no wire harness is connected between the body and engine.


37. DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)

  1. A147555
    Disconnect heater water outlet hose A from the heater unit.


38. DISCONNECT HEATER WATER INLET HOSE A

  1. A147556
    Disconnect heater water inlet hose A from the heater unit.


39. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A147557
    Remove the No. 1 fuel pipe clamp.

  1. A147558
    Pinch the retainer as illustrated, then pull the fuel tube connector out of the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull them to release them.


40. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder.

    HINT:
    Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.


41. REMOVE COLUMN HOLE COVER SILENCER SHEET

  1. A116501
    Remove the floor carpet and 2 clips and remove the column hole cover silencer.


42. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

  1. C117212
    Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

  1. C118005E03
    Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


43. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  1. C125686E01
    Remove clip A, separate clip B from the body and separate steering column hole cover No. 1.

    NOTICE:
    Do not damage clip B.


44. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

B118988
  1. Remove the shift lever knob.


45. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY

B118990
  1. Disengage the 6 claws and remove the shifting hole cover.


46. REMOVE CONSOLE BOX REAR COVER

B118991
  1. Disengage the 8 claws and remove the console box rear cover.


47. REMOVE REAR CONSOLE BOX ASSEMBLY

B118993
  1. Remove bolt <F>.

  1. Disengage the 2 clips and remove the console box rear.


48. REMOVE HEATED OXYGEN SENSOR

  1. A158285
    Disconnect the heated oxygen sensor connector.

  1. Remove the grommet and pull the sensor connector out of the cabin through the floor panel.

  1. A158286
    Remove the wire harness clamp bracket.

  1. A158287E01
    Using SST, remove heated oxygen sensor.
    SST
    09224-00010  


49. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A147560
    Remove the 2 bolts and 2 springs and separate the front exhaust pipe assembly from the exhaust tail pipe assembly.

  1. A147559
    Remove the 2 bolts and 2 springs and separate the front exhaust pipe assembly from the exhaust manifold.

  1. Remove the 3 exhaust pipe supports and remove the front exhaust pipe assembly.


50. REMOVE FRONT AXLE SHAFT LH NUT

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


51. REMOVE FRONT AXLE SHAFT RH NUT

HINT:
The removal procedure for the RH side is the same as that for the LH side.


52. SEPARATE SPEED SENSOR FRONT LH

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


53. SEPARATE SPEED SENSOR FRONT RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


54. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


55. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


56. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


57. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


58. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


59. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


60. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of rope or the equivalent.


61. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


62. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


63. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


64. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A147570
    Set the engine lifter.

  1. A159382
    Remove 2 bolts and remove the engine mounting stay RH.

  1. A147568
    Remove the 6 bolts and nut and remove the engine mounting insulator RH.

  1. A147569
    Remove the through bolt and nut and separate the engine mounting insulator LH.

  1. A147571
    Remove the 6 bolts and remove the engine assembly with transaxle and front suspension crossmember from the vehicle.


65. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. A150573
    Install the engine hangers with the bolts, as shown in the illustration.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }

    Part No.:
    12281-37020 (engine hanger No. 1)
    12282-37010 (engine hanger No. 2)
    91552-81050 (bolt)

  1. Using an engine sling device and a chain block, suspend the engine assembly with transaxle and front suspension crossmember.

  1. Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.


66. REMOVE FLYWHEEL HOUSING SIDE COVER

  1. A159353E01
    Disengage the claw by pulling it outward and remove the flywheel housing side cover.


67. REMOVE STARTER ASSEMBLY

  1. A159354
    Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. A159355
    Remove the 2 bolts and remove the starter assembly.


68. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C106374
  1. Remove the 2 bolts and the control cable bracket.


69. REMOVE MANUAL TRANSAXLE ASSEMBLY

C063143
  1. Remove the 7 bolts and the manual transaxle.


70. REMOVE CLUTCH COVER ASSEMBLY

D025280E04
  1. Put the matchmarks on the clutch cover assembly and the flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


71. REMOVE CLUTCH DISC ASSEMBLY

72. REMOVE FLYWHEEL SUB-ASSEMBLY

  1. A156219E02
    Hold the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A157843
    Remove the 8 bolts and remove the flywheel sub-assembly.


73. REMOVE IGNITION COIL ASSEMBLY

  1. A147572
    Disconnect the 4 ignition coil assembly connectors.

  1. Remove the 4 bolts and remove the 4 ignition coil assemblies.


74. REMOVE RADIO SETTING CONDENSER

  1. A147573
    Disconnect the radio setting condenser connector.

  1. Remove the bolt and remove the radio setting condenser.


75. REMOVE ENGINE WIRE

76. REMOVE NO. 2 VENTILATION HOSE

  1. A147574
    Remove the No. 2 ventilation hose.


77. REMOVE HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)

  1. A147575
    Loosen the clip and remove heater water outlet hose A.


78. REMOVE HEATER WATER INLET HOSE A

  1. A147576
    Loosen the clip and remove heater water inlet hose A.


79. REMOVE NO. 1 RADIATOR HOSE

  1. A147577
    Loosen the clip and remove the No. 1 radiator hose.


80. REMOVE INTAKE MANIFOLD

  1. A147578
    Loosen the clip and separate the water by pass hose.

  1. Separate the No. 1 fuel vapor feed hose from the throttle body.

  1. Loosen the clip and separate the No. 1 vacuum transmitting hose.

  1. A147579
    Separate the ventilation hose.

  1. Loosen the clip and separate the water by-pass hose.

  1. Separate the wire harness clamp from the intake manifold.

  1. A147580
    Remove the 5 bolt and 2 nuts and remove the intake manifold and manifold stay.

  1. Remove the gasket from the intake manifold.


81. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A147581
    Remove the 3 bolts and remove the fuel delivery pipe with the 4 fuel injectors.

    NOTICE:
    Do not drop the fuel injectors when removing the fuel delivery pipe.


82. REMOVE NO. 1 DELIVERY PIPE SPACER

  1. A158247
    Remove the 2 No. 1 delivery pipe spacers.


83. REMOVE INJECTOR VIBRATION INSULATOR

  1. A158248
    Remove the 4 injector vibration insulators.


84. REMOVE FUEL INJECTOR ASSEMBLY

  1. A158249E01
    Pull the 4 fuel injectors out of the fuel delivery pipe.

    NOTICE:
    Place the fuel injector in a plastic bag to prevent foreign matter from entering.


85. REMOVE GENERATOR ASSEMBLY

  1. A159361
    Remove the 2 bolts and remove the fan belt adjusting bar.

  1. A159362
    Remove the terminal cap.

  1. Remove the nut and remove terminal B.

  1. Disconnect the connector and harness clamp.

  1. A159363
    Remove the bolt and remove the generator assembly.


86. REMOVE FAN BELT ADJUSTING BAR

  1. A147584
    Remove the bolt and remove the fan belt adjusting bar.


87. REMOVE VENTILATION HOSE

  1. A147585
    Remove the ventilation hose.


88. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY

89. REMOVE OIL LEVEL GAGE GUIDE

  1. A147586
    Remove the bolt and remove the oil level gage guide.


90. REMOVE WATER BY-PASS HOSE

  1. A147587
    Loosen the clip and remove the water by-pass hose.


91. REMOVE WATER INLET HOSE

  1. A147588
    Loosen the 2 clips and remove the water inlet hose.


92. REMOVE NO. 1 WATER BY-PASS PIPE

A147589
  1. Loosen the clip and disconnect the No. 3 water by-pass hose.

  1. Remove the 2 bolts and remove the water by-pass pipe.


93. REMOVE AIR TUBE ASSEMBLY

  1. A147590
    Remove the 2 bolts and remove the air tube assembly.


94. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A147591
    Remove the 4 bolts and remove the No. 1 exhaust manifold heat insulator.


95. REMOVE MANIFOLD STAY

  1. A147592
    Remove the 3 bolts and remove the manifold stay.


96. REMOVE EXHAUST MANIFOLD

  1. A147593
    Remove the 5 nuts and remove the exhaust manifold.


97. REMOVE WIRE HARNESS CLAMP BRACKET

  1. A147595
    Remove the 4 bolts and remove the 4 wire harness clamp brackets.

← COMPONENTS (from Nov 2006)INSTALLATION (from Nov 2006) →